What Are Dimensions Of Sidewind Handle Shaft Bushings For Direct Weld Jacks

Question

Question:

What are the dimensions of these bushings? Thanks!

asked by: Frank S

0

Expert Reply:

The outer diameter of the # TJD-7000S-BU bushing is 15/16-inches.

The diameter of the hole in the bushing is 1/2-inch.

expert reply by: Jeffrey L

0

Answer 1

I actually went out to our warehouse and measured the: -Replacement Sidewind Handle Shaft Bushing for etrailer and Ram Square, Direct Weld Jacks #TJD-7000S-BU with a set of calipers #PTW80157, and measured: -30.09 mm (1-3/16") for an overall…

view full answer...

Answer 2

Thanks for the pictures! It looks like you have a Ram side wind jack and we do sell replacement parts for it. The jack you were looking at would be a great replacement for it if these parts do are not what you are looking for. The etrailer Square…

view full answer...

Answer 3

I spoke to my contact at Pacific Rim, they said the correct replacement lower flange bushing and washer for your 8,000 lb Ram jack will be the Replacement Sidewind Handle Shaft Bushing for etrailer and Ram Square, Direct Weld Jacks - 7K…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

What Are Dimensions Of Sidewind Handle Shaft Bushings For Direct Weld Jacks

Product Page this Question was Asked From

Continue Researching