Replacement Hardware for Roadmaster Tow Defender Screen

Question

Question:

I recently purchased the Roadmaster Tow Defender Screen from you. First time it was used it worked fine. The second time I installed it on my motorhome upside down. That mistake screwed up the struts on each side of the stinger as well as the blue washers where they are attached. Can I purchase two struts and washers to make the repair?

asked by: Jeff P

0

Expert Reply:

The hardware that includes the washers is part # RM-4800-30. The replacement struts are part # RM-200023-50.

expert reply by: Charles S

0

Answer 1

The Collar Attachment Hardware Kit #RM-4800-30 referenced in your question is simply the replacement hardware for your existing Roadmaster Tow Defender #RM-4700 so I don't think this is what you're needing. It sounds like you might be trying…

view full answer...

Answer 2

We do have replacement hardware for the Roadmaster Tow Defender #RM-4750 which includes a pair of shoulder bolts. You will need Replacement Collar Attachment Hardware Kit for Roadmaster Tow Defender Protective Screen #RM-4800-30.

view full answer...

Answer 3

In order to replace the Replacement Gas Struts part #RM-200023-50 on your Roadmaster Tow Defender Protective Screening part #RM-4750 you will first need to obtain a pick tool or a simple flathead screwdriver will suffice. Once you have this you will…

view full answer...

Answer 4

When the light of the #TST-507-R is on solid that means it has power and the sensors are reporting info that it is picking up. It will occasionally blink as it's transmitting info. When you press the button and it's blinking and beeping…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

While there is one hitch for your 2021 Jeep Cherokee Trailhawk that exits through the bumper, the #e73ZR does not, as the receiver will be below the bumper of your Jeep. The only option for a hitch that protrudes the bumper of your Cherokee Trailhawk…

view full answer...

Answer 7

Hey Dave. To add a hitch to your 2019 Jeep Cherokee, I recommend our etrailer Hitch item #e73ZR. This hitch is custom fit for your Jeep and comes with all hardware necessary to complete the installation. It fits all models including the Trailhawk.…

view full answer...

Answer 8

The plug to connect the #3014-P harness in your 2019 Jeep Cherokee to is behind a black cover that is just to the left of the steering column right above where the carpeting ends. You need to remove the black cover. Check out the picture I attached.…

view full answer...

Answer 9

There are so many different diagrams on how to wire a 4-way round trailer connector because a standard has not been set on how to wire this type of trailer connector. This is likely because 4-way round trailer connectors are not very common. I spoke…

view full answer...

Answer 10

Looks like you have a round 4-way connector in the picture you submitted. The colors you mentioned aren't totally a match for standard colors but they are close. Normally the colors are: White - Ground Return Green - Right Turn and Brake Lights…

view full answer...

Answer 11

Sorry about the confusion. The Curt #C13398 and #C13171 and the etrailer brand #e73ZR would all fit the 2019 Jeep Cherokee Trailhawk. Of the various options, a top choice would be the etrailer #e73ZR because once installed it would be the most…

view full answer...

Answer 12

The wires exiting the rear of your controller serve the following functions. The blue wires carries the brake output from the controller, the white wire is the ground, the black wire supplies 12 Volt power, and the red wire is tied into the vehicle…

view full answer...

Replacement Hardware for Roadmaster Tow Defender Screen

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching