Location of Brake Controller Plug 2019 Jeep Cherokee Limited

Question

Question:

Have a 2019 Jeep Cherokee Limited 2.0 w/Factory Tow Package and Technology Package. Cannot not find any taped connector behind the panel in the area shown on your instructions or on-line. How do I access the factory connection? Does it take a Jeep mechanic to disassemble the underdash? Very frustrated!!!

asked by: Russell S

0

Expert Reply:

The plug to connect the # 3014-P harness in your 2019 Jeep Cherokee to is behind a black cover that is just to the left of the steering column right above where the carpeting ends. You need to remove the black cover. Check out the picture I attached.

If you don't already have a brake controller I recommend the Prodigy P3, part # 90195. It's one of the easiest to setup and use controllers we carry. And it's a Tekonsha controller so it'll work with the # 3014-P. I've linked a demo video of it for you as well.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The wires exiting the rear of your controller serve the following functions. The blue wires carries the brake output from the controller, the white wire is the ground, the black wire supplies 12 Volt power, and the red wire is tied into the vehicle…

view full answer...

Answer 2

I am not sure what you mean by bezel but we do have a couple of wiring harnesses that when combined add a 4-way and 7-way connector to your 2019 Jeep Cherokee. There isn't one single harness available but the two will get you exactly what you…

view full answer...

Answer 3

The factory brake controller connector on your 2021 Jeep Grand Cherokee is located under the dash behind the hood latch, as shown in the provided photo. Keep in mind, the connector will only be there if the vehicle has the factory tow package which…

view full answer...

Answer 4

The Curt Echo Mobile Brake Controller part #C51180 is a very unique brake controller but yes it can activate and actuate the brakes of your trailer. Basically you plug this into the 7-way of your Cherokee and once you sync it to your smart phone it…

view full answer...

Answer 5

If your 2019 Forest River RV Rockwood Geo Pro is prewired for a Furrion RV Observation Camera System part #FOS43TASF then there should be a mounting bracket at the top of the trailer in which the camera would just plug into. If this is not the case…

view full answer...

Answer 6

I can make a list for you of all the parts needed to add a brake controller and 7-way to your 2002 Jeep Liberty, and the prices can be found either on the product page or by scrolling down where the parts will be listed under "Products…

view full answer...

Answer 7

I have another option for you, but the Original Custom Towing Mirror Custom Slide On Mirrors #CTM3400A you were looking at are designed for a 1999-2004 Jeep Grand Cherokee and will not fit your 2019 Jeep Grand Cherokee. At this time there is not a…

view full answer...

Answer 8

To fit the hose in the bumper you will have to take the orange collars off the ends of the RhinoFLEX hose. There should be side storage on your trailer that you can store these and other items in allow the hose by itself to fit as intended. This is…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Location of Brake Controller Plug 2019 Jeep Cherokee Limited

Continue Researching