7-Way Tester for Testing Trailer Side 7-Way

Question

Question:

Im looking for a 7 blade trailer plug trailer side tester.. is there such a tester? I can find the vehicle side tester but not trailer side tester.

asked by: Ken T

0

Expert Reply:

We have the Tekonsha 7-way tester part # 8010 that can test a trailer's wiring as well as Hopkins Tow Doctor Trailer End Test Unit # HM50928. Due to the nature of testing the trailer side of the wiring these kits cost a bit more than the testers for the vehicle.

expert reply by: Jameson C

0

Answer 1

Yes, the circuit labelled "brake" on the Tekonsha Circuit Tester part #8010 would be for testing the brake controller's output on your tow vehicle.

view full answer...

Answer 2

If you are referring to two white wires from the brake magnet that are coming from the rear of each electric brake assembly, then it would not matter which wire is connected to ground and which wire is used for the brake feed. The magnet that…

view full answer...

Answer 3

We do have a number of different lengths of the 3/8" Female Flare x 3/8" Female Flare Swivel propane hose, though I'm not sure if you were asking for 12 foot or 12 inch hose. There is a 12 foot option for this, but not a 12 inch; the…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

Hey Donny! For your Dometic Penguin/Brisk Air 15,000 BTU AC model B59516.711C0-MX, the correct soft start is the #DMC93JF. This is designed for Dometic Brisk II electronic air conditioner units with in-wall thermostats.

view full answer...

7-Way Tester for Testing Trailer Side 7-Way

Continue Researching