Replacement Hitch Pin for Thule Anti Rattle Hitch Lock # THSTL2

Question

Question:

Is the thread on this Threaded Pin a 12mm-1.75? i.e will it fit a Thule Parkway 958 rack? Thank you.

asked by: Jim

0

Expert Reply:

I have confirmed that the Replacement Threaded Pin for Thule Snug Tite Hitch Lock and Anti-Rattle Device, part # TH62RE will fit your Thule Parkway Bike Rack 958.

I actually pulled one off the shelf and tried it in the rack.

expert reply by: Mike L

0

Answer 1

It looks like you have an older Thule T2 Hitch Mount Bike Rack and the correct replacement hitch bolt/pin for this is the Thule Snug Tite Hitch Lock and Anti-Rattle Device part #THSTL2 for locking or Threaded Hitch Pin for Thule part #TH62RE for…

view full answer...

Answer 2

We have the exact anti-rattle hitch lock you are looking for. For your Thule Bike Rack you will need the Thule Snug Tite Hitch Lock and Anti-Rattle Device #THSTL2 which includes a new anti-rattle bolt, lock core, keys, and lock body allowing to…

view full answer...

Answer 3

We do have the hitch bolt that you are needing for your Thule Range 4 Bike RV Rack. If you are just needing the replacement threaded bolt, it is the Replacement Threaded Hitch Pin for Thule Snug Tite Hitch Lock and Anti-Rattle Device #TH62RE. If you…

view full answer...

Answer 4

For your Thule Revolver Bike Rack, you'll need the threaded hitch bolt #TH62RE as the replacement. If you're wanting a locking hitch pin, you could go with part #THSTL2, which includes the locking portion and the threaded hitch bolt.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Replacement Hitch Pin for Thule Anti Rattle Hitch Lock # THSTL2

Product Page this Question was Asked From

Continue Researching