Electronic Lock Out Recommendation for Demco Actuator with Manual Lock Out

Question

Question:

Can you put and electronic lock out on the DM8102222?

asked by: Matthew C

1

Helpful Expert Reply:

Yes, if you wanted to install an electric reverse lockout on the Demco actuator part # DM8102222 you would want the part # DM11993. This is confirmed to fit DA10 actuators like this. When this solenoid has power on it would prevent hydraulic pressure from building in your brake lines and assemblies.

expert reply by: Jameson C

1

Answer 1

The only thing I found on your Dexter 70-7 is the Replacement 13" Rotor for Dexter Disc Brakes #K71-631-00 which has 70-7 stamped on it. The #K71-631-00 fits 8,000 lb. Dexter disc brake kits like the #K71-646-2, #K71-646-2-91 or #K71-646-2-90.

view full answer...

Answer 2

If you wanted to install an electric reverse lockout on the DA10 Demco actuator part #DM8102222 you would want the part #DM11993. This is confirmed to fit DA10 actuators like this. When this solenoid has power on it would prevent hydraulic pressure…

view full answer...

Answer 3

EZ Loader doesn't list a specific bow stop for any of the trailers so you will need to measure to find the right fit. You need the shaft diameter and width of your bracket. For example, if you have a 1/2" shaft and the bracket fits a 3"…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

The Dexter Nev-R-Adjust electric trailer brakes can be manually adjusted. There are a couple teeth of the adjustment wheel that are exposed just under the lever that you referenced. I have attached a photo showing the teeth. You will likely need a…

view full answer...

Answer 11

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 12

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Electronic Lock Out Recommendation for Demco Actuator with Manual Lock Out

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching