Replacement Trailer Grease Seal for an NOK AD2527E Seal on a Boat Mate Trailer

Question

Question:

I have the larger outer bearing race L68110 and the seal I removed was about 1/2 inch thick I see this seal is an NGK AD2527E but I am having a hard time locating one. Is there a new replacement seal its a 3500 Lbs trailer boat mate about 20 years old. inner bearing is the L68149 I believe.

asked by: Paul

1

Helpful Expert Reply:

To replace your NOK AD2527E seal you can use # 168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches. So it will be a tight fit but no other seal is even close.

expert reply by: Michael H

1

Answer 1

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 2

While the #L68149 most likely corresponds to the inner bearing number of your hubs. If this is the case, you have either a 3.5k or a 4.4k axle. In order to know absolutely sure, you need to know the corresponding outer bearing number or the inner and…

view full answer...

Answer 3

Based on the dimensions you listed the correct grease seal is the part #GS-2125DL. This has ID of 2.125", OD of 3.376".

view full answer...

Answer 4

You will want to use a dial caliper or micrometer to measure the inner diameter of the hub you have on your trailer to determine what size cap would be needed. Check out the picture I attached that shows this measurement being taken on a hub. I wish…

view full answer...

Answer 5

Hello Brandon. Well, this isn't reddit, but we do offer one spindle that used the LM67048 (1.25" inner diameter) inner bearing and the LM11949 (0.75" inner diameter) outer bearing. Take a look at the Agricultural Spindle for 3,000-lb…

view full answer...

Answer 6

The 1 inch longer hub face of the #35545E-ST-89 works out to 1/2 inch longer on each side, which isn't a big deal at all. That won't cause a problem. You'll really want the spring centers to be right on, though so the best thing to do…

view full answer...

Answer 7

The Equa-Flex Cushioned Equalizers #LC145546 that includes the 4 wet bolts has greaseable pivot points. This means you can replace the lower bolts that hold the pivot arms in place and replace them with the 4 wet bolts. This kit is rated for 5,000lb…

view full answer...

Answer 8

The MORryde AllTrek 4000 Equalizers for Tandem Axle Trailers #MR29DR are the new upgrade to their counterpart - the MORryde Premium Rubber Suspension Kit for Tandem Axle Trailers MR47ZR. According to MORryde, the AllTrek has been through more intense…

view full answer...

Answer 9

We sure can! The Transcom #TCM 21344 TB cross references to the 10-10 seal we offer, part #RG06-090. The seal has a 2.125 inch ID and a 3.376 OD. It's compatible with a 25580 inner bearing.

view full answer...

Answer 10

Thanks for all of the info on the axle you have on your trailer. Since you have a Dexter 5,200 lb axle with a 6 lug bolt pattern the correct hub/drum you need is the Dexter #K08-201-98.

view full answer...

Answer 11

The correct replacement grease seal for the AD2527E you listed is the part #168233.

view full answer...

Answer 12

Because the 8-14.5 tire that you've got sits on a 14.5" wheel, so you wouldn't be able to switch tire sizes with anything that we have available without also switching to a new wheel as well. If you've got a 6 on 5-1/2" bolt…

view full answer...

Replacement Trailer Grease Seal for an NOK AD2527E Seal on a Boat Mate Trailer

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching