Why do Trailer Suspension Hanger Kits Include Hangers of Different Heights
Updated 08/24/2016 | Published 08/23/2016 >
Question:
What is the purpose of the two different heights for the end brackets and the center brackets? Im working on building a trailer with some axles and springs I already have from a trailer house. Do you have any recommendations on how far to space the brackets? Should the spring bolts just slip right in or should there be some tension/load on them to get the bolts in?
asked by: Kyle
Expert Reply:
The hangers of the part # APTT3 that you referenced are different heights because the center hangers attach to equalizers which then attach to shackles and then finally to the leaf springs. Since there are several components in this arrangement a slightly shorter or longer hanger is used for the center hanger so that when everything is put together the spring ends up sitting level.
Basically the equalizer moves the attachment down and then the shackle straps move it back up and then depending on where that puts things the hanger is at a different height to allow the spring to sit level.
Product Page this Question was Asked From
Triple-Axle Trailer Hanger Kit for Double-Eye Springs - 1-1/2" Front/Rear, 2-1/2" Center
- Trailer Suspension Parts
- Hangers
- Suspension Kits
- Boat Trailer
- Camper
- Car Hauler
- Snowmobile Trailer
- Utility Trailer
- Double Eye Springs
- Triple Axle
- etrailer
more information >
Continue Researching
- Shop: Triple-Axle Trailer Hanger Kit for Double-Eye Springs - 1-1/2" Front/Rear, 2-1/2" Center
- Q&A: How to Flip a 2" Square Axle so the Axle is Below the Springs
- Shop: etrailer Rust-Resistant 3-Leaf Double Eye Spring for 2K Trailer Axles - 20-3/8" Long - Dacromet
- Search Results: 72 inch hub face trailer axles
- Search Results: sp~169275 1020
- Search Results: triple axle
- Search Results: galvanized axle
- Search Results: curved equalizer
- Search Results: galvanized equalizer
- Search Results: equalizer
- Shop: CE Smith U-Bolt Kit for Mounting 2" Square Trailer Axles - 4-1/2" Long U-Bolts - Zinc
- Shop: Triple-Axle Trailer Hanger Kit for Double-Eye Springs - 3-1/4" Front/Rear/Center
- Q&A: What Is The Difference Between TREQE1 And A2252CB-GALV?
- Shop: Curved Equalizer for 1-3/4" Wide Double-Eye Springs - 7-3/4" Long - 9/16" Center Hole
- Shop: Curved Equalizer for 1-3/4" Double Eye Spring - 7-3/4" Long - 9/16" Hole
- Shop: Replacement Shackle Strap - 2-5/8" Long - Galvanized
- Q&A: Why Do Suspension Hanger Kits Have Different Height Hangers
- Shop: Trailer Hitch
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Article: Trailer Wiring Diagrams
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Wiring
- Q&A: Best Suspension Upgrade for 33" Tandem Axles: Road Armor vs Dexter EZ Flex for Ember 22ETS
- Shop: Suspension Enhancement
- Q&A: Can I Use Heavier Rated Leaf Springs on Trailer Without Causing Damage
- Video: How To Choose Camper Leaf Springs
- Article: How to Measure for Trailer Hitch Drop
- Q&A: Which is Better for Highway Use 4.80-12 or 5.30-12 Trailer TIres
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Shop: Brake Controller


