How to Flip a 2" Square Axle so the Axle is Below the Springs
Updated 02/25/2026 | Published 02/16/2026 >
Products Featured in This Question
Question:
I want to convert my oversprung trailer to an undersprung system. My axles are 2 square. Is there a conversion kit for square axles? I have a tandem boat trailer. GVWR is about 7,000
asked by: Stephen L
Expert Reply:
Hey Stephen. All you should need to do to flip a 2" square axle is to use the CE Smith U-Bolt Kit for Mounting 2" Square Trailer Axles item # CE23103. You'll be able to reorientate your axle below your springs with this setup. This kit is designed for 3,500 lbs axles and is sold individually.
Please note you will most likely need to drill new alignment holes opposite of the original ones on the axle tube. A conversion/axle flip kit is more involved because thicker round axles have spring seats welded into them.
What kind of boat do you have?
You can add this information, along with any other questions you have, where it says Add Comment.
Product Page this Question was Asked From
4-Leaf Double-Eye Spring for 3,500-lb Trailer Axles - 25-1/4" Long
- Trailer Leaf Springs
- Double Eye Springs
- 9/16 Inch Eye
- Nylon Bushing
- 3500 lbs
- 1-3/4 Inch Wide
- 4 Leaf
- 25-1/4 Inch Long
- Standard Grade
- etrailer
more information >
Continue Researching
- Search Results: slipper springs trailer leaf springs
- Search Results: axle flip
- Shop: Triple-Axle Trailer Hanger Kit for Double-Eye Springs - 1-1/2" Front/Rear, 2-1/2" Center
- Video: All You Need to Know About the Dexter Trailer Springs Over-Under Conversion Kit
- Search Results: dust cap tool
- Video: Review of Lippert Trailer Suspension Parts - Equalizer Upgrade Kit - LC53CK
- Shop: etrailer Rust-Resistant 3-Leaf Double Eye Spring for 2K Trailer Axles - 20-3/8" Long - Dacromet
- Search Results: 72 inch hub face trailer axles
- Search Results: sp~169275 1020
- Search Results: bearing 02475 and 25580 trailer bearings races seals caps
- Search Results: triple axle
- Shop: CE Smith U-Bolt Kit for Mounting 2" Square Trailer Axles - 4-1/2" Long U-Bolts - Zinc
- Q&A: Why do Trailer Suspension Hanger Kits Include Hangers of Different Heights
- Q&A: What Equalizer Upgrade Would Be Best for My 2026 Jayco Eagle 28BHU?
- Video: Review of RV Ride Control Trailer Suspension Parts - Alignment and Lift Kits - RR23QX
- Shop: 4-Leaf Double-Eye Spring for 5,000-lb Trailer Axles - 25-1/4" Long
- Shop: Triple-Axle Trailer Hanger Kit for Double-Eye Springs - 3-1/4" Front/Rear/Center
- Shop: 3-Leaf Slipper Spring w/ Flat End for 2,900-lb Trailer Axles - 30" Long
- Q&A: How To Flip Square Trailer Axle For Ground Clearance
- Q&A: What Is The Difference Between TREQE1 And A2252CB-GALV?
- Shop: Dexter Trailer Springs Over-Under Conversion Kit
- Article: The 5 Best Trailer Drop Hitches You Can Buy
- Article: How to Troubleshoot Your RV Air Conditioner
- Q&A: How To Measure For Replacement Shackles to Install Lippert Road Armor Equalizer
- Q&A: Can you Upgrade Leaf Springs for Increased Ground Clearance on a Trailer
- Q&A: What are Common Trailer Wheelbases
- Article: Trailer Tire Sizing
- Shop: Performance Chip Tuners
- Shop: Floor Mats
- Video: Detailed Breakdown of the Nylon Bushing



Stephen L.
2/19/2026
Sounds good. I have a 24' Skipjack fly bridge. Made some mods to the trailer, Built over sprung springs to I had a lower center of gravity as need to trailer boat as much as 50 mi. one way and wanted lower CG for driving. Now I use an duo prop out drive which is longer and need clearance when not lifted and washing down. Thank you for the info.