Thule Atlantis 1600XT Slide Strip Recommendation

Question

Question:

Hi. I own a Thule Atlantis 1600xt. A few months back I ordered replacement quick grip mounts for my cargo box. Upon installation, the replacement strips that were shipped to me did not fit the holes in the box maybe I am installing wrong?. I was sent the Evolution strips. Are these compatible with the Atlantis box?

asked by: Jessica

0

Expert Reply:

I checked with Thule and the correct slide strip you need is actually the part # TH05401 and not the part # TH05308 that you referenced.

expert reply by: Jameson C

0

Answer 1

The long plastic strips in the EasySnap Mounting hardware are part #TH05308. They are often called slide strips and as such they are not meant to be permanently glued down because then the feet would not be able to slide. If there is glue residue…

view full answer...

Answer 2

The Replacement Slide Strip #TH05401 is the correct replacement for your Thule Ascent 1700 605. The Replacement Quick Grip Mount Assembly #TH05738 and Thule Snapfit Cradle Replacement Kit #TH68NB are the correct parts for your cargo carrier.

view full answer...

Answer 3

Would you be able to send me some photos of your roof box and the area where the mounting hardware is installed? If you have a newer Thule/MB cargo box then the Replacement Quick Grip Mount Assembly #TH05738 should work but if I could see some photos…

view full answer...

Answer 4

Hi Johnny; the key shield can be replaced using the #05771. To replace the lock cylinder you can use the #TH450200.

view full answer...

Answer 5

Thanks so much for the photo and the info on your cargo box model. I'm not 100 percent certain which part you are referring to, so I will list all of the available replacement parts for your Thule Atlantis 1600XT cargo box, which I confirmed with…

view full answer...

Answer 6

The only slide strip we offer is part #TH05308, and it is designed for the Thule Evolution Roof Box. The Thule Quick Grip #TH05738 is designed to fit Thule Ascent, Atlantis and Force cargo boxes.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Thule Atlantis 1600XT Slide Strip Recommendation

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching