How to RV Propane Tank Covers Mount to Trailer

Question

Question:

Hi I just wonder is there any installation instruction how to mount the cover? thanks

asked by: Rodney

0

Expert Reply:

Typically what people do to mount the propane tank covers like the part # CAM40565 is to use a bungee cord like # EM06755 to secure it below the tanks. The cover has two tabs on the bottom of it that allow for the hooks of the strap to be attached to so that you can secure it.

expert reply by: Jameson C

0

Answer 1

I attached a chart that has all of the recommended lug nut torque specs for trailer wheels. Based on your studs being 1/2 inch, your wheels being 15 inches in diameter, and your lug nuts being coned you would want to torque your lug nuts to 90-120 ft…

view full answer...

Answer 2

Assuming that when you tested the resistance of the brakes you were testing the two wires on each magnet and getting 2.0 and 2.8 ohms the magnets on your trailer are not working correctly and will need to be replaced. For 7" brakes you should…

view full answer...

Answer 3

In order to clear the leader hose and regulator mounting bracket on your 20 lb propane tank with the Camco RV Polyethylene Propane Tank Cover part #CAM40565 you would more than likely need to rotate the tank so that the backet and leader hose are…

view full answer...

Answer 4

The MB Sturgis Horizontal 2-Stage Propane Regulator #108221 that you referenced does not come with a bracket. I wish we offered one but we do not as most applications already have a bracket for the regulator and this is designed to fit standard…

view full answer...

Answer 5

Both single-stage #CAM59013 and dual-stage #108221 regulators will both reduce pressure down to 11" WC, but the difference is the stability of the output pressure. The single-stage regulators quickly reduce the pressure down and give you a bit…

view full answer...

Answer 6

Though the design is slightly different you can use the Camco Horizontal 2-Stage Propane Regulator #CAM59323 in place of the Cavagna Model 524AS 2-stage regulator. I have linked a video review of this regulator for you.

view full answer...

Answer 7

Yes it is super simple! The Complete Propane Tank Holder Mounting Kit for 20-lb Tanks part #37220BL is secured to the tongue of the trailer using self tapping screws. #14 self tappers have always worked out really well and they will go into the three…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

How to RV Propane Tank Covers Mount to Trailer

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching