Replacement Barrel Clips for Pilot Bully Nerf Bar Pads

Question

Question:

I have Bully Nerf bars and the clips to hold the pad are no longer good. The plastic step is good. Is it possible to get just the clips? The part number the clips would fit is NB-PAD2. Thanks,

asked by: Steve T

0

Expert Reply:

Actually the Westin barrel clips part # 23-0002 are the same as what comes with the part # NB-PAD2 that would fit your bars so these would work well for you.

expert reply by: Jameson C

0

Answer 1

Hey Adam! The step pads we have are universal-ish. They're made with specific bars in mind, but if the "pegs" match up their spacing with what you have, then you can still use ours even if it is a different brand. The Replacement Step…

view full answer...

Answer 2

We do have a 21x3 inch replacement pad. It is the Replacement Step Pad for Westin E-Series Nerf Bars - 21" Long x 3" Wide - Qty 1, #23-0001. Unfortunately this pad has 5 posts. The closest 4 post replacement pad we have is the Replacement…

view full answer...

Answer 3

I'm really not sure why they're so hard to find, but we do have a number of step pads that might work. It looks like the closest one we've got available is going to be the Replacement Step Pad for Westin Platinum Series Nerf Bars -…

view full answer...

Answer 4

It sounds like you need replacement step pad #23-0001. It is 21 inches long, 3 inches wide, and the pin measurements are nearly identical. I say nearly because as you can see in the picture I have included they are not exactly the same. But as you…

view full answer...

Answer 5

The closest replacement pad we have to what your mentioned is the Replacement Step Pad for Westin Signature Series Nerf Bars - 19-3/4" Long - Qty 1 #26-0001. I have attached 2 photos of one of this replacement pad. One photo shows the outside…

view full answer...

Answer 6

The Westin Replacement E-series Step Pad, #23-0001, measures 3-5/8, 5-5/8, 6-3/8, 3-5/8 inches from one end pin to the other. I have attached a photo showing the measurements I took for you. It is 21 inches long and 3 inches wide. This certainly does…

view full answer...

Answer 7

We carry 5 types of replacement Westin step pads with five pegs: Replacement Step Pad for Westin Platinum Series 20" long x 4" wide #24-50020. Replacement Step Pad for Westin Oval Tube Steps 18" x 4" #22-5002. Replacement Step Pad…

view full answer...

Answer 8

I do not recognize the part number you mentioned, however, I can give you a few options for replacement step pads for your running boards / nerf bars. The Replacement Step Pad #23-0001 that you were looking at is specifically made for the Westin…

view full answer...

Answer 9

We have two options to replace the step pads on your Aries Round Nerf Bars item #AA203044 and you're going to need to take a look at the bottom of one of yours to see which is the right one for your F-150. The Replacement Step Pad for Aries…

view full answer...

Answer 10

The Replacement Step Pad for Aries 3" Wide Oval Nerf Bars #AA86FR measures 6.496” apart center-to-center for the inner pins, and the two outer pins measuring 17.795” apart center-to-center. It's not uncommon for replacement pads to fit from…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Replacement Barrel Clips for Pilot Bully Nerf Bar Pads

Continue Researching