What Do Abbreviations EB and XL Mean on Trailer 7-Way

Question

Question:

What does XL and EB stand for on a pin connector for a trailer? LT is left turn? RT is right turn? BU is back up? TM is Tail Marker tail lights? EB is ???? XL is ????

asked by: Gene

0

Expert Reply:

EB would stand for electric brake on a trailer connector. This is the circuit that carries voltage to the brake assemblies of the trailer. XL would be auxiliary and is typically a 12 volt power circuit used for lights or maintenance charge on a trailer battery.

expert reply by: Jameson C

0

Answer 1

You will want a Non-Sag sealant like the alpha Systems Alpha Thane 5160 Non-Sag Sealant for RVs #AL83KV. It sticks to wood, metal and glass. It will not run or drip. It is weather-resistant and flexible so it wont crack and peal off while your travel…

view full answer...

Answer 2

What you are describing is normally the result one 1 of 3 issues: First, there could be some corrosion in or on the connectors on the vehicle or trailer side or both. Second there could be a bad ground. Bad grounds can cause all sorts of bizarre…

view full answer...

Answer 3

If the light bulb is disconnected from the socket, there should not be any continuity between the running lights (brown wire) and the ground (white wire). It sounds to me as if you may have a shorted or pinched wire somewhere along in the…

view full answer...

Answer 4

Based on the 30-92-XXX partial part number you provided, it sounds like you have Bargman 92 Series taillights. These taillights measure 8-9/16 inches long x 4-9/16 inches wide x 2-1/8 inch thick. I have some options for LED taillights for you,…

view full answer...

Answer 5

The LED Trailer Tail Light Driver #328-003-81LBM1 and Passenger #328-003-81BM1 are going to be the closest to the Bargman #30-92-004 you currently have. These lights are all red and do not have provisions for the reverse light. Another option you…

view full answer...

Answer 6

Based on the numbers that you provided in your question, the Bargman Replacement Lens #30-2-708 should be the correct lense for your existing assembly. The lens itself measures 8-5/8 inches wide and 4-1/2 inches in height. It has a depth of 1-7/8…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

What Do Abbreviations EB and XL Mean on Trailer 7-Way

Featured Help Information

Miscellaneous Media

Continue Researching