Dutton-Lainson Trailer Winch - DL11004 Strap Length Recommendation

Question

Question:

How many feet of strap will this winch hold? Would DL24242 work? Thanks in advance

asked by: Phil

1

Helpful Expert Reply:

I spoke with my contact at Dutton Lainson and the max length (and recommended length) strap to use with the Dutton-Lainson Worm Gear Hand Winch # DL11004 is 20 feet like the # DL24242.

expert reply by: Jameson C

1

Answer 1

For your application, I recommend the Dutton-Lainson Hand Winch,TUFFPLATE Finish, Two Speed with Direct Drive - Hand Brake - 2,500 lbs #DL14830. This hand winch when mounted to a secure anchor point will allow you to pull your trailer up the incline…

view full answer...

Answer 2

I do have a solution for you, however the Dutton-Lainson Hand Winch #DL11004 referenced in your question is actually designed for use with a polyester strap and not cable. For the Dutton-Lainson 2,000 pound hex gear hand winch that uses cable you…

view full answer...

Answer 3

The Pro Series Standard Brake Winch - Cable Only - 1,500 lbs #PSKR15000301 is a great option for your pop up camper. It requires a minimum line pull of 50 lbs to operate, but has a first line layer capacity of 1500 lbs. For your application, you…

view full answer...

Answer 4

If you're going to use a winch to raise and lower your popup you will want a winch that power loads both in and out. With a winch that will only power load in you will only be able to raise the popup and not lower with the winch. We have the…

view full answer...

Answer 5

The only types of winches we can recommend for hoisting like what you are wanting to do are the worm gear winches like the #DL11011 that you referenced. This winch has more than enough capacity so it would fit and work well. For a similar winch that…

view full answer...

Answer 6

The Dutton-Lainson Heavy Duty Brake Winch part #DL10808 has a braking mechanism that locks in place when the handle is released. In order to obtain a ratcheting mechanism with this winch you will want to replace the handle with the Brake Winch…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Dutton-Lainson Trailer Winch - DL11004 Strap Length Recommendation

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching