How To Remove Lens of Optronics LED RV Interior Light # RVILL33 to Access Mounting Holes

Question

Question:

How do I remove the lens so I can mount the light with screws 4 holes provided? It looks like it should slide off but I dont want to break it. Thanks

asked by: Tom W

0

Expert Reply:

To remove the lens of the Optronics # RVILL33 lamp, you simply push the lens away from the switch as you can see in the photo I've provided and in the video. Once the lens is removed, you can easily access the mounting holes.

expert reply by: Mike L

0

click to enlarge

Answer 1

I cannot be for certain but it looks like you have a standard 194 type bulb in which case yes, it would just pull straight out but may take a bit of wiggling if there is any corrosion holding it in place. In order to then replace the bulb we have…

view full answer...

Answer 2

Yes, the Furrion RV Power Cord Adapter - 30A Female to 20A Male #FP3122RSB will work to convert your 30 amp service trailer to accept power from the 20 amp shore power pedestal. The drawback is that you'll not be getting full power to your…

view full answer...

Answer 3

You could use the Furrion RV Power Cord Adapter - 30A Female to 20A Male - Black Item #FP3122RSB but you won't be able to run as much in your RV since you're not pulling a full 30amps. You won't find a 2 prong plug because the ground…

view full answer...

Answer 4

LED lights such as pancake light #277-000339 are typically brighter than their incandescent counterparts. The light draws 3 watts which is comparable to a 30 watt fluorescent bulb so that should help you to determine if the LEDs will be brighter than…

view full answer...

Answer 5

Hey June, the lumen output for the #277-000339 is right at 110 but we had a customer leave us a review on this light and they specifically said the lumen output wasn't very bright so if you are wanting something BRIGHT this wouldn't be what I…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

How To Remove Lens of Optronics LED RV Interior Light # RVILL33 to Access Mounting Holes

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching