Recommended Grease for the Blue Ox Sway Pro System

Question

Question:

Which grease should I use on the grease zerks in a Blue Ox Sway Pro head? Thanks!

asked by: Scott D

1

Helpful Expert Reply:

Blue Ox recommends LubriMatic Moly EP Grease for the Blue Ox Sway Pro System. For that you would want the part # LM54FR.

If you need a grease gun for that you would also need the part # L30200.

I have linked both parts mentioned above to this page for your convenience.

expert reply by: Jackie C

1

click to enlarge

Answer 1

You are correct that in the Blue Ox SwayPro Owner's Manual they do recommend use molybdenum grease on both the hitch ball and the spring bars. The LubriMatic Moly EP Grease #LM54FR in a grease gun, such as #L30480, will work well. You could use…

view full answer...

Answer 2

You are correct that the Blue Ox SwayPro weight distribution systems do require the use of molybdenum grease. For that you would want the part #LM54FR. If you need a grease gun for that you would also need the part #L30200.

view full answer...

Answer 3

Hello Susie, Great question. When installing the Blue Ox SwayPro Weight Distribution w/ Sway Control for 2" Hitch - 10,000 lbs GTW, 1,000 lbs TW #BXW1000 you will want to start with 9 links under tension. It is step #9 in the instructions, I…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Recommended Grease for the Blue Ox Sway Pro System

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching