Bolt-Through Hardware Kit for Fulton Swivel Jack

Question

Question:

Does this part work for a 2000 lb. Fulton swivel jack?

asked by: John

0

Expert Reply:

The bolt-through hardware kit for Fulton swivel jacks, part # F0933325S00, fits all bolt-through Fulton swivel jacks regardless of capacity. This fits a mounting plate like part # P9012-00 as is found on jacks like # FXP10.

expert reply by: Adam R

0

Answer 1

Hi Billy, The F500277 is for a Fulton trailer jack that is no longer in production. The 4 3/8" x 3 3/8" bracket measurements are typically from an older style weld on trailer jack, we used to have a version that fit those dimensions, but it…

view full answer...

Answer 2

Hey Tim. There are only two jacks that will fit your current mounting bracket and they are both Fulton F2 jacks rated at 1,600 lbs. I have listed them below: Fulton F2 Swing-Up Trailer Jack, Dual 7" Wheels, Sidewind item #F1413060334 Fulton F2…

view full answer...

Answer 3

Thank you for providing the picture of your existing mount. This was helpful to idenfication and I have attached it to this post. As you mentioned, the 90 degree snap in holes are 3" apart from center to center. It may be helpful to note that…

view full answer...

Answer 4

Hi George; there are some replacement parts available for the Fulton F2 Boat Trailer Jack #F1413020134. We have the following: -Replacement Handle and Crank Kit for Fulton F2 Swing-Up Jacks #F500134 -Replacement Pull Pin Kit for Fulton F2 Swing-Up…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Bolt-Through Hardware Kit for Fulton Swivel Jack

Continue Researching