How to Separate Fan Tastic Roof Vent Fan Blade From Vent Motor

Question

Question:

I need to remove the fan blade from the drive motor in order to properly clean this unit,. is there a special tool to remove this fan blade. the trailer is a 2011 model 2250

asked by: Daniel M

0

Expert Reply:

To remove the fan blade of a Fan Tastic Roof Vent # FV802250 you will need to first remove the screen on the underside. You will want to then remove the vent cover lid from the outside of the trailer as well.

There are four screws from the top of the cover that hold the blade and motor to the top of the vent housing. You will be able to remove the motor and blade at this point.

There is then an allen wrench screw sized 3/32 inch that will need to be loosened on the shaft of the fan that will then allow the blade to release. Check out the picture I attached to see it.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Hey Jay, the correct replacement converter to replace what you have now that is compatible with LifePO4 batteries would be the part #PD69RR that you referenced. Progressive Dynamics likes to change their part numbers a lot and create revisions of…

view full answer...

Answer 2

It sounds like the seals have failed and the grease from the bearings has come out during travel. Also it is possible that if you have an EZ lube axle with a grease zerk at the end to add grease but use a single lip seal, the pressure can blow out…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 6

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

How to Separate Fan Tastic Roof Vent Fan Blade From Vent Motor

Featured Help Information

Miscellaneous Media

Continue Researching