Pin Hole to End of Shaft Dimension for the Bulldog Replacement Jack Handle Part # BD500105

Question

Question:

is the distance from the retaining pin hole center - to the end of the 1/2inch crank shaft 2 3/4?

asked by: Andy

0

Expert Reply:

The distance from the center of the retaining pin hole to the end of the shaft on the part # BD500105 measures 3 inches.

expert reply by: Jameson C

0

click to enlarge

Answer 1

I do carry replacement parts for the Dutton-Lainson Sidewind Swivel Trailer Jack, part #DL22800 that you have referenced. The replacement handle is the Dutton-Lainson Replacement Handle, part #DL22448 and the bushings for the handle you will need are…

view full answer...

Answer 2

Both the Fulton 800 lb Handle #F0933301S00 and the 1,500 lb Handle #F0933305S00 have the same diameter so you just need to make sure that the distance from the end of the handle to the pin hole is similar to what you currently have.

view full answer...

Answer 3

I actually went out to our warehouse and measured the: -Replacement Sidewind Handle Shaft Bushing for etrailer and Ram Square, Direct Weld Jacks #TJD-7000S-BU with a set of calipers #PTW80157, and measured: -30.09 mm (1-3/16") for an overall…

view full answer...

Answer 4

I measured the Replacement Sidewind Handles #MJ-1000B-HD and #MJ-1500B-HD and found that they both have a diameter of 1/2" and part MJ-1000B-HD measures 2" from the end of the handle to the center of the pin hole while part MJ-1500B-HD…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Pin Hole to End of Shaft Dimension for the Bulldog Replacement Jack Handle Part # BD500105

Continue Researching