Location of Taillight Fuse in Power Distribution Box in 2007 Nissan Titan

Question

Question:

I know it is in the distubution box under the hood but where is it located.

asked by: Paul

0

Expert Reply:

Based on my research, in your 2007 Nissan Titan the 10-amp fuse for taillights is located in the IPDM, which is behind the power distribution box in a separate enclosure (closer to the passenger). The IPDM, or Intelligent Power Distribution module, has two 10-amp fuses, one of which is for the taillight circuit. You may need a long screwdriver and needle nose pliers to get the fuse out. It should be fuse position 32.

expert reply by: Adam R

0

Answer 1

Hey Edwin, this is a known issue with certain Nissan models. A lot of times there will be some wiring already in place but no relays. The Tekonsha #118266 comes with the necessary relays as well as the 7-way plug but sometimes there still is a…

view full answer...

Answer 2

This is a very common issue with newer Nissan vehicles like your 2019 Nissan Frontier. There is a missing relay needed to activate the trailer running light circuit. The running light relay can be installed or replaced with #C57000. One likely place…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 12

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Location of Taillight Fuse in Power Distribution Box in 2007 Nissan Titan

Continue Researching