Weight of Brophy Aluminum and Steel Scissor Steps

Question

Question:

What is the weight on both of these?

asked by: Dean

0

Expert Reply:

The Aluminum Scissor Steps # AS03 that you referenced weigh 15 lbs and the Scissor Steps # SS03 weigh 29 lbs.

As you can see, aluminum is much lighter.

expert reply by: Jameson C

0

Answer 1

It sounds like you need to re-calibrate the zero point on your Lippert Ground Control 3.0 #LC304136 system. Below I've listed out the steps you'll need to follow and will allow you to use the auto leveling again. Zero Point Calibration The…

view full answer...

Answer 2

It sounds like going from the existing 2 step assembly on your Coachmen Trailblazer Toy Hauler to a 3 step assembly will be the best option for reducing the height of the first step. I recommend looking at the TorkLift GlowStep Revolution Scissor…

view full answer...

Answer 3

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 4

Hey Donny! For your Dometic Penguin/Brisk Air 15,000 BTU AC model B59516.711C0-MX, the correct soft start is the #DMC93JF. This is designed for Dometic Brisk II electronic air conditioner units with in-wall thermostats.

view full answer...

Answer 5

That’s a great question Chadwick, and this is one of those situations where the change in technology really matters. The GE Appliances Low-Profile RV AC w/ Heat Pump part #GE26RR will replace your current ARC13AACBL2 setup, but it’s important to know…

view full answer...

Answer 6

The Brophy Scissor Step Bracket #TSSB will install on the edge of your tailgate. You will have to drill two holes for the L shaped pins. After drilling, all you have to do is simply insert the L pins into those holes and attach you Brophy steps! For…

view full answer...

Answer 7

Hi Mark, I don't have any database to confirm for you if the MORryde Safe-T-Rail Telescoping RV Hand Rail part #MR54BR will fit your Forest River IBEX 19QBS. However, the handle may fit if your trailer meets certain standards the handle requires…

view full answer...

Answer 8

We can set you up with new steps so that you love your whole camper setup, steps included. Based on the information you provided, I recommend taking a look at the Brophy Camper Scissor Steps #AS25. This is a 5-step assembly that can expand to between…

view full answer...

Answer 9

Hey Patrick! The Brophy Camper Scissor Steps #AS25 have the most steps with 5 steps. How long do you need them to be? At the full 48" height the steps will stick out 46" from the mounting bracket. These are designed for a 40"–48"…

view full answer...

Answer 10

Hello Todd, Nice job upgrading your setup with the SEAFLO #SE57FR pump and the #SE38FR accumulator, that’s a solid combo. The accumulator tank comes pre-charged to about 10 psi from the factory, but it’s really important to check and adjust that…

view full answer...

Answer 11

Hey Judy, normally when this occurs with a truck bed camper the issue is that there happens to be too much weight in the back of the truck camper behind the rear axle. Can you try moving any of that weight forward in the camper when on the road and…

view full answer...

Answer 12

That is a good question, and you can leave your current fold-out steps up and in the folded position when installing the mounting bracket of the Brophy Scissor Steps. The reason is, the bracket will be installed just underneath the door so as long as…

view full answer...

Weight of Brophy Aluminum and Steel Scissor Steps

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching