Bright Interior Light Recommendation for Interior of Cargo Trailer

Question

Question:

Hi, What is the brightest light you have of the inside of a Cargo Trailer? Mine is 7 x 14 x 6 painted white.

asked by: Kevin W

0

Expert Reply:

For a bright interior light for your cargo trailer I would recommend the Opti-Bright LED interior light part # ILL08COB.

This light produces 1400 Lumens so it would be very bright. The dimensions of the lens of this light are 4 by 16-1/2 inches.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Zinc plated screws are going to be the best option for use with aluminum to resist galvanic corrosion. This corrosion you are referring to is from two dissimilar metals reacting so you want to use the most similar metals when installing your E-track…

view full answer...

Answer 2

Hey Jimmy! We use two main types of sealant on trailers. For flat surfaces you want self-leveling like the LaSalle Bristol XTRM Universal Self-Leveling Sealant #34427034145-1. For vertical surfaces you can use non-sag like the LaSalle Bristol XTRM…

view full answer...

Answer 3

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 4

You are correct. Red lights should always be as close to the rear of the trailer as possible. With that also said, if you wanted to use something like the Optronics Thinline LED Trailer Fender Light w/ Bracket #MCL67ARB on the fender, you will want…

view full answer...

Answer 5

All the brake controller needs to sense a trailer connection so that you can test it is a slight amperage draw on the output circuit. For that you can use a circuit tester like the part #PTW2993 with one pin grounded and the other on the output pin.…

view full answer...

Answer 6

The marker and clearance lights you have now ground with a single wire hence why you have two wires total, one for power and one for ground. If the marker or clearance light only has one wire then this wire is for power and the light grounds though…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Bright Interior Light Recommendation for Interior of Cargo Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching