Can I Purchase Just the Parts Needed to Add Wireless Controls for Air Lift Air Bag System

Question

Question:

I have an airlift system with the auto height control. the sensor that goes on the frame has malfunctioned and I need to replace it. I was thinking of changing to a wireless system that I can control in the cab. I see the systems, but they all have a compressor which mine is almost new. is there a kit to just add the control to an existing system?

asked by: Jim B

1

Helpful Expert Reply:

I spoke with my contact at AirLift and it is going to be more cost effective to purchase the Air Lift WirelessONE Compressor System for Air Helper Springs, # AL25980, or the Air Lift WirelessAIR Compressor System for Air Helper Springs, # AL74000, which are the entire kits.

Purchasing the parts needed to add the in-cab controls would exceed the cost of the kit. Since you mention that your compressor is almost new, you could possibly sell it to offset the cost of the kit.

expert reply by: Leah S

1

Answer 1

As long as your 2015 Ford E-350 Van has a factory 7-way at the rear of it all you would need to install the controller is the harness part #3034-P. This adapter plugs into the connector behind your vehicle's dashboard. To reach the connector,…

view full answer...

Answer 2

It sounds like you have a wireless air compressor system like the Air Lift WirelessAIR Compressor System part #AL74000EZ. If that's the case, you could remove the air compressor from this system and create your own wired one. In order to do this,…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

Hey Douglas, whenever available I recommend going with the HD version of the Roadactive kits like the part #RAS3611-YHD that fits your 2022 Ford F-150 4WD. The extra capacity of this kit over the non-HD basically doesn't have any downside aside…

view full answer...

Can I Purchase Just the Parts Needed to Add Wireless Controls for Air Lift Air Bag System

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching