Replacement Trailer Taillight Assembly Recommendation for 3348 Capsule that Has Blown on Trailer

Question

Question:

My units calls for #3348 Replacement for boat trailer tail lights. Is this a correct current product number. Please advise asap if new product replacement is required. Do not require LED. Thank you.

asked by: Al

0

Expert Reply:

The 3348 is a Wesbar capsule that is no longer available. What you would need instead is the part # 403026 for the left hand side and/or part # 403076 for the right hand side.

expert reply by: Jameson C

0

Answer 1

The older generations of the Wesbar submersible low-profile lights came with sealed light bulb capsules that are not replaceable. If your capsule is sealed, then your best option is to replace the lights with new lights like part #403026 and #403076.…

view full answer...

Answer 2

We do have the Optronics ST37 series lights that have the connector instead of bare wires. Aero Pro light #ST37RPG has the plug but just for the running lights, brake, and turn signal wires. The ground is separate. The matching right hand side is…

view full answer...

Answer 3

The Wesbar light that the replacement lens #102641 you were looking at fits has been discontinued. The company that bought Wesbar has been getting rid of a lot of their lights so it is unlikely you will find it. However, the Optronics Combination…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Replacement Trailer Taillight Assembly Recommendation for 3348 Capsule that Has Blown on Trailer

Featured Help Information

Miscellaneous Media

Continue Researching