Replacement Grease Seals For Trailer With 3,500 Lb Axle

Question

Question:

i have a 1989 boat trailer i need bearing seals the old number on the seals is as follows tcm 171266 tb or t8 id is 1.71 od is 2.53

asked by: Ryan C

0

Expert Reply:

It sounds like you have a 3,500 lb axle and are replacing the bearing seals.

The closest seals to that size we offer are the TruRyde Seals for Trailer Bearings, part # RG06-050. These have an inside diameter of 1.719 and outside diameter of 2.565. I was unable to find the number you referenced, but the seal I mentioned above is a replacement for a Transcom part number 171255TB.

expert reply by: Jeffrey L

0

Answer 1

There really should be a flat washer between the outer bearing of your hub and the nut that holds it on. The washer protects the back side of the bearing from the edges and points on the back side of the spindle nut. The Washer For 1 inch Spindle,…

view full answer...

Answer 2

Typically 4-way wiring consists of 18 and 16 gauge wires. For a 4-way that has all 16 gauge wire you would want the Wesbar 4-Pole Flat Connector #W787264. The part #HM38138 uses 18 gauge for all wires but the white that uses 16 gauge.

view full answer...

Answer 3

The marker and clearance lights you have now ground with a single wire hence why you have two wires total, one for power and one for ground. If the marker or clearance light only has one wire then this wire is for power and the light grounds though…

view full answer...

Answer 4

Trailer wheel lug nuts that are 1/2-inch inside diameter typically have a 20-TPI thread pitch (20 threads per inch). Most lug nuts also use a 60-degree-coned profile like #CE11051, but a 90-degree like #STN569 is also available for 9/16-inch studs.…

view full answer...

Answer 5

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 6

We have a variety of Fulton replacement caps for trailer jacks but I wasn't able to locate what your 0951503-00 looks like even on Fulton's site. With that being said, here are the options that we have: Replacement Round Cap for Standard…

view full answer...

Answer 7

If you have a trailer wheel that has a 6 lug setup you are going to have a bolt pattern of 6 on 5-1/2 inches. This is the standard 6 lug wheel bolt pattern that trailer rims have. If you are unsure you can check out the help article I attached that…

view full answer...

Answer 8

I couldn't be 100% positive about which wheel studs you'd need without seeing the trailer and being able to measure. I just don't have enough information. This bein said, by virtue of the trailer having a 5 on 4-1/2 inch wheel bolt…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Replacement Grease Seals For Trailer With 3,500 Lb Axle

Product Page this Question was Asked From

Continue Researching