What is the Inside Width of CE Smith Light Duty, Vertical Bunk Bracket # CE10605G

Question

Question:

Can you give me the dimension inside the u shape section?... the distance between the two holes. if that makes sense.

asked by: Tim B

0

Expert Reply:

Yes the inside with of the CE Smith Light Duty, Vertical Bunk Bracket # CE10605G is 1-3/4 inches. It is designed for 2x4 boards or 2x6 boards. A 2x4 or 2x6 does not actually have a 2 inch width. It is 1-3/4 inches. So I am not sure why they even call them 2x4s or 6s.

expert reply by: Michael H

0

click to enlarge

Answer 1

Hey Jim, so I reached out to my contact at BedSlide, and unfortunately, they do not have any kind of dimensional drawing they can send. Also we do not stock these here, so I am not able to go grab one and measure. They did send me a copy of the…

view full answer...

Answer 2

Yes, there is David. If you take a look at the picture below, of the Caliber Marine Slides for Boat Trailer Bunks item #CA26AJ, you'll see one of our etrailer stickers. To the right of it is a channel that runs the entire center of the slide. The…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

What is the Inside Width of CE Smith Light Duty, Vertical Bunk Bracket # CE10605G

Product Page this Question was Asked From

Continue Researching