Front Mount Trailer Hitch Receiver for a 2006 Lincoln Mark LT

Question

Question:

Will this hitch fit on 2006 Lincoln Mark LT without any modifications?

asked by: Robert

0

Expert Reply:

The installation instructions for Curt front mount receiver # 31352, see link, do not specify any vehicle modification for installation on your 2006 Lincoln Mark LT. But it is always possible that some trimming of an air dam or fascia may be needed on some models.

We also have Draw-Tite hitch # 65043 which should not require any modification. The receiver will sit below the front fascia. I have linked videos and instructions for both hitches for you.

expert reply by: Michael H

0

Answer 1

The Curt Front Mount Trailer Hitch Receiver #31352 is not a fit for the 2 wheel drive 2003 Ford Expedition. It will only fit the 4x4 model. I called to confirm with my Tech contact at Curt and he said the mounting isn't the same because the…

view full answer...

Answer 2

This front-mount hitch receiver, part #31352, is the correct specified part for your 2005 Ford Expedition 4WD. I spoke to my contact at Curt Manufacturing regarding the third mounting hole, which evidently is missing from your Expedition. I am told…

view full answer...

Answer 3

For your 2004 Ford Expedition Eddie Bauer, the Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2" #31352 is the only front mounted hitch receiver that will be compatible and is only compatible for 4x4 model. The Aries Grille Guard - 1…

view full answer...

Answer 4

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 5

The EcoHitch Hidden Front Mount Trailer Hitch Receiver #306-X7352 that you referenced is confirmed to fit your 2017 MB Sprinter 3500 and while I'm not sure it's quite comparable to disturbing an angry hornet's nest, the install process is…

view full answer...

Answer 6

The receiver tube portion of the Curt Trailer Hitch Receiver part #C13002 will extend out past the rear bumper fascia on the 2015 Cadillac SRX so the center knockout panel cannot be reused unless modified. This will be the case for all aftermarket…

view full answer...

Answer 7

EcoHitch does not allow their instruction manuals to be linked, so I cut out and added the most relevant portions of the installation of the EcoHitch Hidden Front Mount Trailer Hitch Receiver #306-X7352. This hitch, which is a confirmed fit for your…

view full answer...

Answer 8

The Curt Front Mount Receiver, item #31352, has a 9,000 Lbs. Max. Line Pull, and lower fascia trimming may be required on some models. The part that may need to be trimmed is the plastic fascia that is attached to the bottom of the chrome bumper on…

view full answer...

Answer 9

Good question! The blade stiffeners that come with the Detail K2 Snowplow #K2AVAL8422 don't necessarily have to be used. I reached out to my contact at Detail K2 who said that the only time that those stiffeners really need to be used is if you…

view full answer...

Answer 10

The exact procedure will depend on which transfer case your truck is equipped with. For a manual shift transfer case, you'd do as follows: Release the parking brake. • Turn the key in the ignition to the OFF position. • Place the transmission in…

view full answer...

Answer 11

There are two hitch pin holes on the shank of the Gen-Y Adjustable 2-Ball Mount part #325-GH-524 to allow for compatibility with different receivers. Trucks typically use the one closest to the vertical portion and SUVs typically use the one furthest…

view full answer...

Front Mount Trailer Hitch Receiver for a 2006 Lincoln Mark LT

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching