Coolers

Hello Anthony. It sure does! The CVT Timber Creek Annex for Car Camping #RG35ZV will work on virtually any SUV or crossover, so it can absolutely be used on a 2024 Subaru Crosstrek.

Hi Randal! As the etrailer Hard Tonneau Cover - Folding - Fiberglass Reinforced Plastic #e98RV for your 2024 Toyota Tundra 6-1/2 Foot Bed with the Deck Rail System has weather seals on top of the bed rails, you will not need drain tubes. From what I…

Hey Janet! The 70" measurement is the overall width of the Thomas Payne Trifold RV Loveseat and Sleeper #LC34FC. The overall dimensions are 70" x 37" x 37". The sleeping surface is 60" wide x 70" long x 19" high.

The awning roller that is installed on the Solera 12V Power RV Awning Conversion Kit #LC434724 that you referenced could be wound not tight enough and the motor doesn't have enough spring assist. Or it's possible the battery of your RV is…

The main difference between a Class III hitch and a Class IV hitch is the capacities they set for the hitches. Class III hitches are rated for up to 6,000 lbs GTW with 600 lbs TW whereas a Class IV is rated for up to 12,000 lbs GTW and 1,000 TW. For…

I went out to the warehouse and pulled Pins and Thumb Clips #EQ95-01-9415 to measure them for you. The diameter is 3/8 of an inch. The usable length is just under 2-1/2 inches (2.45 inches). And the opening is 2.46 inches by 1.5 inches.

We offer 3/8-inch diameter Replacement Snapper Pin #JFC-PN whose measurements are noted in the photo I linked for you. This item matches the original; I confirmed by going to our warehouse and measuring the pin included with your Husky Super Brute…

My contact at Atwood recommended using a pin at least 3/8 in diameter and 2-3/4 inches long. I'd recommend using a snapper pin, part #JFC-PN which has those dimensions.

My contact at Curt Manufacturing advised that they do not offer the replacement Wire Lock Lynch Pins (shown as part number 10 in their instructions, which are linked) that secure their TruTrack's trunnion bars at the head end but he said…

For your Geo Pro Camper with a 59" frame rails width the DrawTite Multi-Fit Motor Home Trailer Hitch part #82201 is an excellent choice. I like the really low profile it offers allowing it to fit snugly up under the camper. It mounts with the…

To use the Pro Series RB3 on two trailers would only require you to get a second set of spring hangers. For that you would want the part #RP6637 and for the chains part #55630.

To choose a weight distribution system you will need to go by the total tongue weight of the set up. This is calculated by taking the tongue weight of the trailer, when loaded and ready to tow, and adding to that the weight of anything loaded behind…

Hello Anthony. It sure does! The CVT Timber Creek Annex for Car Camping #RG35ZV will work on virtually any SUV or crossover, so it can absolutely be used on a 2024 Subaru Crosstrek.

Hi Randal! As the etrailer Hard Tonneau Cover - Folding - Fiberglass Reinforced Plastic #e98RV for your 2024 Toyota Tundra 6-1/2 Foot Bed with the Deck Rail System has weather seals on top of the bed rails, you will not need drain tubes. From what I…

Hey Janet! The 70" measurement is the overall width of the Thomas Payne Trifold RV Loveseat and Sleeper #LC34FC. The overall dimensions are 70" x 37" x 37". The sleeping surface is 60" wide x 70" long x 19" high.

The awning roller that is installed on the Solera 12V Power RV Awning Conversion Kit #LC434724 that you referenced could be wound not tight enough and the motor doesn't have enough spring assist. Or it's possible the battery of your RV is…

The main difference between a Class III hitch and a Class IV hitch is the capacities they set for the hitches. Class III hitches are rated for up to 6,000 lbs GTW with 600 lbs TW whereas a Class IV is rated for up to 12,000 lbs GTW and 1,000 TW. For…

I went out to the warehouse and pulled Pins and Thumb Clips #EQ95-01-9415 to measure them for you. The diameter is 3/8 of an inch. The usable length is just under 2-1/2 inches (2.45 inches). And the opening is 2.46 inches by 1.5 inches.

We offer 3/8-inch diameter Replacement Snapper Pin #JFC-PN whose measurements are noted in the photo I linked for you. This item matches the original; I confirmed by going to our warehouse and measuring the pin included with your Husky Super Brute…

My contact at Atwood recommended using a pin at least 3/8 in diameter and 2-3/4 inches long. I'd recommend using a snapper pin, part #JFC-PN which has those dimensions.

My contact at Curt Manufacturing advised that they do not offer the replacement Wire Lock Lynch Pins (shown as part number 10 in their instructions, which are linked) that secure their TruTrack's trunnion bars at the head end but he said…

For your Geo Pro Camper with a 59" frame rails width the DrawTite Multi-Fit Motor Home Trailer Hitch part #82201 is an excellent choice. I like the really low profile it offers allowing it to fit snugly up under the camper. It mounts with the…

To use the Pro Series RB3 on two trailers would only require you to get a second set of spring hangers. For that you would want the part #RP6637 and for the chains part #55630.

To choose a weight distribution system you will need to go by the total tongue weight of the set up. This is calculated by taking the tongue weight of the trailer, when loaded and ready to tow, and adding to that the weight of anything loaded behind…