Fender Trim Specs:
Installation Notes:
Drilling will be required for installation if any of the holes in the product do not line up with the holes on the vehicle
More Information >Fender Trim Specs:
Installation Notes:
Drilling will be required for installation if any of the holes in the product do not line up with the holes on the vehicle
More Information >Fender Trim Specs:
Features:
Outfit your Jeep Wrangler JL or Gladiator with Aries front fender flares. Included LED lights provide extra visibility from the front and sides, and function as running lights and turn signals. Lightweight aluminum construction is rustproof.
Installation Notes:
Drilling will be required for installation if any of the holes in the product do not line up with the holes on the vehicle
More Information >Fender Trim Specs:
Installation Notes:
Drilling will be required for installation if any of the holes in the product do not line up with the holes on the vehicle
More Information >Fender Trim Specs:
Installation Notes:
Drilling will be required for installation if any of the holes in the product do not line up with the holes on the vehicle
More Information >Fender Trim Specs:
Installation Notes:
Drilling will be required for installation if any of the holes in the product do not line up with the holes on the vehicle
More Information >Fender Trim Specs:
Installation Notes:
Drilling will be required for installation if any of the holes in the product do not line up with the holes on the vehicle
More Information >Videos
for Fender Trim
Help Articles
for Fender Trim
Expert Answers
for Fender Trim
Hi Richard! It sounds like you're needing to install the Load Resistor Kit for LED Turn Signals #DI34ZR on the turn signals you've installed on your toolbox. Since LEDs don't require as much power as incandescent…
view full answer...Yes, there is! To install the Redarc Tow-Pro Elite Brake Controller item #RED63RR in your 2023 Subaru Ascent you will need the Plug-In Wiring Adapter for Electric Brake Controllers item #3062-P. The brake controller port will be underneath the dash…
view full answer...Since Valley went out of business there are no direct replacement parts that are available but a repair kit like the Curt #C25194 for 2" Curt Couplers may be compatible. What I recommend doing is replace your coupler completely as…
view full answer...I do have an option for you but roof rails won't work very well on a teardrop trailer, even if you were able to get the rails to conform, it's likely the accessories would bind due to the steep angles. Instead, you will need to use…
view full answer...I must recommend that you replace the hub/drum as well when changing the size of your braking assemblies because the surface area on the old drums may not line up with the new braking assemblies which is why I recommend replacing both at the same…
view full answer...The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.
view full answer...Do you by any chance mean 235/80-16 and 235/85-16? Because there isn't a 275 trailer tire size that I have seen. If so then the widths are the same between the two 235 sizes. The difference is overall diameter. The 235/80-16 is 30.9 inches…
view full answer...All of the 3500-lb-rated trailer axles that we offer are 89-inches in length from hub face to hub face and have spring seats at a 74-inch spacing. Your 3500-lb axle may be different so you'll want to measure your hub face and spring seat…
view full answer...The recommended lug nut torque for your 7,000lb axle depends on a few factors like wheel size, stud size etc. Check out the attached photo which shows the torque specs for a variety of applications. I see you were looking at the Dexter Nev-R-Adjust…
view full answer...Congrats on the new trailer! You will need a sliding 5th wheel hitch. A standard fixed hitch like the Curt A20 item #C16140 won't provide you with the necessary clearance you'll need. You'll end up running the nose on your…
view full answer...Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…
view full answer...Looks like you have an older version of the 21007-92230 that you referenced which fits the following: 1973 - 1991 Chevrolet C/K Series Pickup 1973 - 1991 GMC C/K Series Pickup 1967 - 1983 Ford F-100, F-150, F-250, F-350 Standard Bed models 1992 -…
view full answer...