Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…
Hey Craig. Had to go measure this myself out in our warehouse, I see we don't have this listed. That opening is large enough for a 1" thick panel. What are you looking to panel?
Hey Pam, welcome back! To replace your Pentair Shurflo Revolution 4008 Series By-Pass Pump, I recommend the Seaflo Diaphragm Pump for Boats and RVs item #SE57FR. This is a 12v powered three gallon per minute pump that is rated up to 55 psi. It works…
Hello Richard, Congratulations on the KZ Confluence 18RB! That is a really nice camper, and I like that KZ packed quite a bit into an 18-foot floorplan while still giving you a slide for some extra room inside. Yes, installing the etrailer RV…
Hi LaRue! The etrailer RV Slide-Out Topper #e67QV does include the awning rail track. This is everything you need for a complete slide-out topper installation. If you already have Solera mounting brackets installed from the factory, you will also…
Hey Brian! Yes, the Firestone Ride-Rite Air Helper Springs #F89VV will fit your 2025 Toyota Tundra. That is just the generic picture attached to that page, I can see how it would be confusing. These are designed to mount over the axle, and are…
Hi Mike, The JR Products Screen Door Slider part #37211185 has a depth of 1 1/4". That makes its overall dimensions 12 1/16" long x 11 7/8" wide x 1 1/4" deep. Though it isn't perfectly square at 12" x 12", it is…
Hey Kevin, yes we have the SumoSprings kit part #SS46KJ that is a fit for your 2025 Chevrolet Silverado 2500 HD. This is the medium density foam spring provides 2,800-lb support capacity at 50% compression and also requires no drilling for install!…
Your current microwave has the dimensions of 29-15/16 W x 16-7/16 H x 15-3/8 D which is almost identical to the Furrion part #FMCM15SS which we know works really well and is reliable so it would be a really great and easy solution.
Hello Paul, There is one thing I like to have when I'm out enjoying the wilderness, and that's a toilet that feels like I'm at home. Well, I found just that for you. Since you're replacing the Dometic 300 in your 2021 Winnebago Minnie…
That is correct Trevor! The Progressive Dynamics 4500 Series RV Converter w/ Charge Wizard and AC/DC Distribution Panel item #PD4590K18LS8 would be the correct replacement. This is a 90-amp 2-in-1 AC/DC distribution panel and converter charger that…
Easy place to shop. Fast delivery and great products. Very happy with my purchase.
Ed
Boynton Beach, FL
RV Door Parts for Folding Doors made easy
Replace broken or damaged carriers by reusing the same hardware for attachment to the door panels. These RV door parts keep folding doors working smoothly, and if new hardware is needed it is best to source same or similar locally.
Swap broken or damaged carriers one at a time and reuse the original hardware. Dry-fit the carrier in the track to check alignment before fastening. If using rivets, confirm tool and stem size to avoid a mismatch. After securing, slide the door to verify smooth travel.
Yes, replacements have been reported to fit perfectly. Still, match the carrier style and size to your original before installing. Test-fit in the track to confirm smooth movement. If a rivet fit is tricky, bring the old rivet to match diameter and grip range before fastening.
No special fasteners are required. Reuse the existing screws or rivets from your folding door. If you need new hardware, get same or similar locally. Finding a rivet that fit was not easy for some, so take the old one to compare lengths and diameters.
They typically secure using the same hardware already on your folding door. Remove the damaged carrier and reuse the original screws or rivets to attach the replacement to the door panels. If new hardware is needed, source same or similar locally. Double-check fastener size so the carrier slides in the track smoothly.
Filters
