Lift Supports - Gas Struts, RV Designer

Hey Raymond, since the 5k rated etrailer jack part #e55ZV is rated higher than the 3.5k option you also mentioned it will work a little bit quicker since it won't be working quite as hard. With that said it's not a fast jack by any means. It…

The factory brake controller connector on your 2021 Jeep Grand Cherokee is located under the dash behind the hood latch, as shown in the provided photo. Keep in mind, the connector will only be there if the vehicle has the factory tow package which…

Without pulling the hub off and checking the seal it is hard to say if it truly blew out the seal or if it was incidental leakage. The safe bet is to replace the seal. Since you have the Dexter D44 axle it will take a 10-19 seal. For a pair use…

Between the Rack'Em Double Barrel Utility Trailer Tailgate Lift Assist #RA-27C and the Gorilla-Lift Utility Trailer Tailgate Lift Assist #GL1, we do in fact sell more of the Double Barrel #RA-27C. As far as quality of the product, the Double…

The HammerBlow Trailer Coupler, like the #BD028463 is a coupler that will mount to the from frame of a trailer and be used to attach to a hitch ball on the back of a vehicle. It mounts to 50 degree A-Frame Tongue and will couple to a 2-5/16 in hitch…

I attached a picture I got from Buyers Products that has the dimensions of the Buyers Products Hook and Keeper for Enclosed Trailer Door #BP64FR that has the dimensions you are looking for.

The Lippert 4,400 lb axles use the same bearings and seals as a Lippert 3,500 lb axle so you can use the Bearing Kit for #84 Spindle part #BK2-100 or just the Grease Seal part #RG06-050.

Hey David, Sure, there are a couple of other options, as you're right, you shouldn't have to replace the Replacement Center Cap for 15" or 16" Aluminum Viking Series Wheels - Chrome #TA65FR every year. If you just want to go to a…

Hi Josh, yes, these jacks part #e94RV can absolutely be used on an aluminum trailer, but you’re right to be thinking about galvanic corrosion, especially with the kind of outdoor exposure you’re describing. Anytime you’re bolting steel components to…

Hello Mark, thanks for reaching out. The Bulldog Powered-Drive Kit #BD1824200100 can work with the Fulton Magnum Series 12K jack. Basically those Fulton Magnum jacks made after 2003 are virtually identical to the Bulldog 12k jacks. Since your trailer…

The closest option we have is the part #SP01-120 which is U-bolt that is 1-1/2 inches wide, has a diameter of 1/2 inch, and has a length of 5 inches.

The Holland Binkley model 48,000 series jacks are very similar to the Bulldog Square Jack - Drop Leg w/ Spring Return #BD182815 which can utilize the Bulldog Powered-Drive Kit for Single-Speed Jacks w/ 12,000-lb Capacity #BD1824200100. Your current…

Hey Raymond, since the 5k rated etrailer jack part #e55ZV is rated higher than the 3.5k option you also mentioned it will work a little bit quicker since it won't be working quite as hard. With that said it's not a fast jack by any means. It…

The factory brake controller connector on your 2021 Jeep Grand Cherokee is located under the dash behind the hood latch, as shown in the provided photo. Keep in mind, the connector will only be there if the vehicle has the factory tow package which…

Without pulling the hub off and checking the seal it is hard to say if it truly blew out the seal or if it was incidental leakage. The safe bet is to replace the seal. Since you have the Dexter D44 axle it will take a 10-19 seal. For a pair use…

Between the Rack'Em Double Barrel Utility Trailer Tailgate Lift Assist #RA-27C and the Gorilla-Lift Utility Trailer Tailgate Lift Assist #GL1, we do in fact sell more of the Double Barrel #RA-27C. As far as quality of the product, the Double…

The HammerBlow Trailer Coupler, like the #BD028463 is a coupler that will mount to the from frame of a trailer and be used to attach to a hitch ball on the back of a vehicle. It mounts to 50 degree A-Frame Tongue and will couple to a 2-5/16 in hitch…

I attached a picture I got from Buyers Products that has the dimensions of the Buyers Products Hook and Keeper for Enclosed Trailer Door #BP64FR that has the dimensions you are looking for.

The Lippert 4,400 lb axles use the same bearings and seals as a Lippert 3,500 lb axle so you can use the Bearing Kit for #84 Spindle part #BK2-100 or just the Grease Seal part #RG06-050.

Hey David, Sure, there are a couple of other options, as you're right, you shouldn't have to replace the Replacement Center Cap for 15" or 16" Aluminum Viking Series Wheels - Chrome #TA65FR every year. If you just want to go to a…

Hi Josh, yes, these jacks part #e94RV can absolutely be used on an aluminum trailer, but you’re right to be thinking about galvanic corrosion, especially with the kind of outdoor exposure you’re describing. Anytime you’re bolting steel components to…

Hello Mark, thanks for reaching out. The Bulldog Powered-Drive Kit #BD1824200100 can work with the Fulton Magnum Series 12K jack. Basically those Fulton Magnum jacks made after 2003 are virtually identical to the Bulldog 12k jacks. Since your trailer…

The closest option we have is the part #SP01-120 which is U-bolt that is 1-1/2 inches wide, has a diameter of 1/2 inch, and has a length of 5 inches.

The Holland Binkley model 48,000 series jacks are very similar to the Bulldog Square Jack - Drop Leg w/ Spring Return #BD182815 which can utilize the Bulldog Powered-Drive Kit for Single-Speed Jacks w/ 12,000-lb Capacity #BD1824200100. Your current…