Hi Kassi! I do have a couple options that will fit your 2024 Chevy Colorado WT with 2 wheel drive, but the Timbren Suspension Enhancement System - Rear Axle #T83AV is specifically for the 4 wheel drive models. With that said, you will want one of the…
While we don't have replacement parts for a Model 70LP actuator, we do have a great replacement for it. Like the 70LP, these actuators are a fit for a 2" hitch ball, but they just have a slightly larger capacity at 7,500 lbs. You didn't…
The towing capacity of the 2003 Chevrolet Avalanche 1500 with 5.3L V8 and 4.10 rear axle is 8100-lbs. For a 7600-lb GVWR travel trailer the resulting 500-lb safety margin is adequate/low-ish. With a trailer that weighs substantially more than the tow…
I would be happy to help you. For your 2006 Kenworth T300 I recommend the Tekonsha Prodigy P2 Trailer Brake Controller item #90885. This controller ties into the brake stoplight switch that's usually located above the brake pedal, which is what…
Hey Brad, to replace your Tie Down Engineering LP70 actuator, I recommend going with the Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-20. This actuator will fit on 3" wide channel tongues, will work with 2" balls, and has a 7,500 lb…
The Furrion #FACR15SA-PS 15,500 BTU unit that you referenced is a replacement for Furrion only and is not offered with compatible ceiling distribution box. I do have a solution though. To replace your Single-Zone, Stand-Alone Dometic Duo-Therm Brisk…
If the front arm/hinge on your Yakima SkyBox Cargo Box like the SkyBox 12 #Y07334 isn't unhooking due to the carrier being over-stuffed, then your only real option is to try and wiggle around your cargo enough to get some clearance between it and…
The exact replacement hub assemblies you need for your BD2-545-17 are the etrailer Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 #AKHD-545-35-K that you referenced.
Hey Neil, so we can help but we don't have a rebuild kit or an exact replacement for the Tie Down model 70lp that you referenced. The Dexter Disc #DX73FR or Drum #DX67FR actuator is going to be your best option. These are weld on actuators but we…
Based on the number you mentioned you have a 3,500 lb AxleTek hub so for a version that has the 6 on 5-1/2 inch bolt pattern you are wanting you'd need the part #AKHD-655-35-EZ-K.
The receiver tube portion of the Curt Trailer Hitch Receiver part #C13002 will extend out past the rear bumper fascia on the 2015 Cadillac SRX so the center knockout panel cannot be reused unless modified. This will be the case for all aftermarket…
Dial in a clean, custom look with MagnaFlow exhaust tips. Choose clamp-on for an easy slip-over install without welding, or go weld-on when you want a seamless fit; just measure the outside diameter of your tailpipe to match. Some styles re-direct exhaust downward to help keep cargo carriers and gear away from heat.
With a weld-on MagnaFlow tip, it can be made to fit, but matching sizes gives a cleaner connection. Tack it first to hold position, then finish the weld and clean up as needed. Work in a well-ventilated area and keep ignition sources away from fuel vapors.
Yes, clamp-on MagnaFlow tips slip over the existing tailpipe and tighten with a band clamp. Cutting isn't needed when the tip slips over your pipe. Confirm your tailpipe's outside diameter and make sure there's enough straight length to seat the clamp securely.
Measure the outside diameter of your tailpipe and match it to the tip's stated fit size. Clamp-on tips are sized to slip over a specific OD. Weld-on styles that match your pipe's diameter will not slide over; line them up and weld in place. If you want a certain look, you may need to trim the existing pipe to position the tip.
Yes. A MagnaFlow tip that redirects exhaust downward can help protect items on a cargo carrier from excess heat. Also consider raising the carrier further from the exhaust to add clearance. Verify your tailpipe's outside diameter so the redirecting tip you pick will fit.
2-1/4 Inch Tailpipe Fit
2-3/4 Inch Tailpipe Fit
Filters
