Hi Kassi! I do have a couple options that will fit your 2024 Chevy Colorado WT with 2 wheel drive, but the Timbren Suspension Enhancement System - Rear Axle #T83AV is specifically for the 4 wheel drive models. With that said, you will want one of the…
While we don't have replacement parts for a Model 70LP actuator, we do have a great replacement for it. Like the 70LP, these actuators are a fit for a 2" hitch ball, but they just have a slightly larger capacity at 7,500 lbs. You didn't…
The towing capacity of the 2003 Chevrolet Avalanche 1500 with 5.3L V8 and 4.10 rear axle is 8100-lbs. For a 7600-lb GVWR travel trailer the resulting 500-lb safety margin is adequate/low-ish. With a trailer that weighs substantially more than the tow…
Hey Rick, yes you can use the longer Equalizer shank part #EQ90-02-4500 that you referenced in place of what you have now to get a little more length from your towing setup. While this is longer and would in theory apply more leverage it doesn't…
I would be happy to help you. For your 2006 Kenworth T300 I recommend the Tekonsha Prodigy P2 Trailer Brake Controller item #90885. This controller ties into the brake stoplight switch that's usually located above the brake pedal, which is what…
Hey Brad, to replace your Tie Down Engineering LP70 actuator, I recommend going with the Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-20. This actuator will fit on 3" wide channel tongues, will work with 2" balls, and has a 7,500 lb…
The Furrion #FACR15SA-PS 15,500 BTU unit that you referenced is a replacement for Furrion only and is not offered with compatible ceiling distribution box. I do have a solution though. To replace your Single-Zone, Stand-Alone Dometic Duo-Therm Brisk…
If the front arm/hinge on your Yakima SkyBox Cargo Box like the SkyBox 12 #Y07334 isn't unhooking due to the carrier being over-stuffed, then your only real option is to try and wiggle around your cargo enough to get some clearance between it and…
The exact replacement hub assemblies you need for your BD2-545-17 are the etrailer Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 #AKHD-545-35-K that you referenced.
Based on the number you mentioned you have a 3,500 lb AxleTek hub so for a version that has the 6 on 5-1/2 inch bolt pattern you are wanting you'd need the part #AKHD-655-35-EZ-K.
Hey Neil, so we can help but we don't have a rebuild kit or an exact replacement for the Tie Down model 70lp that you referenced. The Dexter Disc #DX73FR or Drum #DX67FR actuator is going to be your best option. These are weld on actuators but we…
WOW! I am impressed! I called to place my order and real person answered, spoke perfect English, albeit a slight southern accent, and my order was sent within a day, shipped quickly and I had it a few days later. I saved over a hundred dollars over local and installed it my self. I cant imagine how that they could do any better. THANKS!
Eric
Cedar Springs, MI
Angle Cut Exhaust Tips for clean style
Angle cut tips add a sharp, finished look. Some clamp-on choices slip over your existing tailpipe and tighten with a band clamp, so no cutting or welding is needed, while weld-on options are also available. Match the tip to your tailpipe's outer diameter—options like 3-1/2 inch, 4 inch, and 5 inch—and confirm the length will fit; these are mainly cosmetic and have zero effect on gas mileage.
If a black version isn't available, you can paint a stainless angle cut tip with high-heat black spray paint. The tailpipe area doesn't get as hot as headers, so this paint can hold up well. Clean and scuff the surface, apply light coats, and let it cure per the paint directions.
Exhaust tips are mainly cosmetic and won't have much effect on how the exhaust system functions. You shouldn't see a noticeable change in fuel economy from adding a tip. Choose the look you want and the attachment style that fits your setup.
Clamp-on angle cut tips slip over the existing tailpipe and bolt into place with a band clamp. No cutting is needed for this style. Measure the outer diameter of your tailpipe to pick the right size. Check that you have enough straight pipe length so the tip and clamp can seat fully.
Yes, angle cut tips are universal-fit as long as the tip matches your tailpipe's outer diameter. Some trucks use larger tubing, so measure first. If your pipe is slightly undersized, an exhaust shop can add a sleeve or carefully expand the pipe for a tight fit. Also confirm there's room for the tip's length.
Filters
