Truck Bed Mats Specs:
Features:
Use this tailgate mat with your BedRug truck-bed floor mat to extend slip resistance and 1/4" cushioning to your vehicle's tailgate. Be good to your knees when unloading cargo or working in the back of your truck - you might need them later.
More Information >Truck Bed Mats Specs:
Features:
Use this tailgate mat with your BedRug truck-bed floor mat to extend slip resistance and 1/4" cushioning to your vehicle's tailgate. Be good to your knees when unloading cargo or working in the back of your truck - you might need them later.
More Information >Truck Bed Mats Specs:
Features:
BedRug XLT mat upgrades your vehicle bed with a 3/4" thick layer of polypropylene and a soft carpet top. Provides a flat work surface, prevents skidding loads, and cushions your cargo. Covers your bed floor, tailgate, and tailgate gap.
More Information >Truck Bed Mats Specs:
Features:
BedTred Impact mat upgrades your vehicle bed with a 3/4" thick layer of polypropylene and a tough thermoplastic top. Provides a flat surface, prevents skidding loads, and cushions your cargo. Covers your bed floor, tailgate, and tailgate gap.
More Information >Truck Bed Mats Specs:
Features:
BedRug XLT mat upgrades your vehicle bed with a 3/4" thick layer of polypropylene and a soft carpet top. Provides a flat work surface, prevents skidding loads, and cushions your cargo. Covers your bed floor, tailgate, and tailgate gap.
More Information >Truck Bed Mats Specs:
Features:
BedTred Impact mat upgrades your vehicle bed with a 3/4" thick layer of polypropylene and a tough thermoplastic top. Provides a flat surface, prevents skidding loads, and cushions your cargo. Covers your bed floor, tailgate, and tailgate gap.
More Information >Videos
for Truck Bed Mats
Help Articles
for Truck Bed Mats
Expert Answers
for Truck Bed Mats
To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…
view full answer...Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well.…
view full answer...The hub/drum you sent in a picture of is a Lippert 8,000 lb axle hub with an 8 on 6-1/2 inch bolt pattern designed for oil-bath applications. The correct replacement then is the #8-285-10UC3-A.
view full answer...The proper replacement inner assembly member for your UFP 34043 would be indeed be the the Dexter #DX99FR which is compatible with disc brakes. The replacement has an electric lock out and has a 7500K capacity and is intended to work with a 2 inch…
view full answer...The serial number and VIN are typically printed on a label or plate placed somewhere on the trailer's pole tongue, although it could possibly found elsewhere on the trailer frame, possibly on…
view full answer...It sounds like you are on the right track for tracking down where the issue is. That said, the integrated brake controllers they were putting in trucks around 2008 weren't as reliable as the…
view full answer...The Torklift Hitch Extension part #TLE1636 that you referenced can tow a trailer that weighs 6,700 lbs like you what you have but you would need to use a weight distribution system with it to have the needed capacity as without a WD system…
view full answer...I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do…
view full answer...It sounds like you need to re-calibrate the zero point on your Lippert Ground Control 3.0 #LC304136 system. Below I've listed out the steps…
view full answer...The 1-7/8 inch width is what is rounded up to 2 inches which is a standard width for winch straps. The 14 foot length is not something we carry. I recommend the Hand Winch Strap with Safety Hook,…
view full answer...Hey Jeff, the WeatherTech ImpactLiner Custom Truck Bed Mat #WT99KF would get secured to your bed using the TechHold Retention Device (see image attached) which is just a adhesive ball and socket. Basically, one the ball end would get stuck to the…
view full answer...The recommended lug nut torque for your 7,000lb axle depends on a few factors like wheel size, stud size etc. Check out the attached photo which shows the torque specs for a variety of applications. I see you were looking at the Dexter Nev-R-Adjust…
view full answer...