Summer Starts Here - Save up to 70%
# 1
Hollywood Racks Sport Rider SE Bike Rack for 2 Electric Bikes - 2" Hitches - Frame Mount
I have a Dirty Sixer 36" wheel bike and my wife has an electric bike. This rack handles them both very easy. This is one of the only bikes racks the 36er will fit on. We are extremely happy with the purchase and will more than likely be purchasing another one in the near future. Assembly was very easy!!
This bike rack works great for our 2 Lectric 2.0 e-bikes. We mount it on our 2019 Honda Ridgeline. It folds up nicely when it’s on the truck and we are using our bikes. The locking mechanisms work well also. I contacted support for a smaller hook arm to clamp B over the bike frame. They knew exactly what I needed and shipped it - no problem.
# 2
Hollywood Racks Sport Rider SE2 Bike Rack for 2 Bikes - 2" Hitches - Frame Mount
Even though the rack is an import, I was well pleased with the ease of assembly and the quality of the racks manufacturing. I would recommend that you purchase one if you are in need of a 2-bike rack assembly. I also purchased the 3-wheeled trike rack and assembled it. I'm totally satisfied with both my purchases at this time
I love this bike rack! It came quickly and it was super easy to put together. I am a 66 year old female, and if I can do it, anyone can do it! It has everything that was advertised. It has the built in locks, which is awesome, and all the moving parts are easy to use. My bike does not move going down the road and that is a big plus for me! I did rap a bungee cord around my bike frame and the frame hook bar for my piece of mind, but it is not necessary. I highly recommend this bike rack.
# 3
Thule Hitching Post Pro Bike Rack for 4 Bikes - 1-1/4" and 2" Hitches
The good: I like the way the bikes are held in and the ability to add the upright adapters to the bike frame holders. The straps are quality too. For a jeep with a spare tire, this is the perfect length to clear it. This rack is 5 stars from the bike holders to the base of it. The bad: the 2"receiver adapter and bolt are insufficient. I wish they made this in a solid 2" hitch. The entire setup is held into the receiver by a very short bolt. It only goes about half way into the receiver tube. So your hitch is only "secured" on one side. A hitch pin or bolt should go through the receiver tube completely imo so it can be secured on the other end with a retaining clip or nut. Because this only goes in the one side, the entire weight of the rack plus bikes are held tight to one side of the receiver by the undersized bolt and washer. A few bumps down the road and that bolt loosens. Now instead of distibuting the weight of the rack and bikes on the receiver and post, it's completely up to the bolt to keep you from losing the rack. The bolt threads get damaged too. I took this down a dirt road and nearly lost everything. I had to buy my own bolt with hd fender washers and lock washers to correct this. Thule should've provided this from the start. The current short bolt design where only one side of the receiver secures the rack is unacceptable. This rack is 1 star at best for the connection to the receiver.
I bought this bike rack back in April but wanted to make sure I used it to give the best review. First I want to say I did a lot of research on bike racks and found this one to be the best one to fit my needs. The best price I found was on etrailer.com, at the time it was When I called the customer service to place my order, I spoke to Dan. He was very pleasant on the phone and took the time and listened to what I needed and understood my concerns. I ordered the bike rack and also ordered the Thule Snug Tite Hitch Lock and Anti-Rattle Device and the Thule Cable Lock w/ One Key System Lock. Dan suggested I also get the Thule Bike Adapter Bar, which I never even thought of getting. Delivery was in about two business days, which was really fast and at the time of order they were running a special free delivery over $99. When I went to put it together I noticed I was missing the flat cap screw M6 x 16mm, part number #853-5787-02. I emailed Dan and within 24 hours received an email that the part was sent out and also in the email their was a link to track the order. After I received the part I did notice that the flat cap screw was actually in the 2 inch adaptor sleeve. The instructions were very easy to read, and it took me about 20 minutes to put together. I did have an issue when I positioned the stinger into the cradle, with the 8mm locking nut, it was not staying tight and when I took it off I noticed the threads inside were gone, so I ended up going out to Lowes and buying a new one and its holds perfectly fine. I also had a question about that part because it is not a locking part and was worried someone would try to steal the rack. I contacted etrailer.com to find if they make a locking device for this and they said no but I can contact Thule to double check, I'm still waiting for an answer back from Thule. The weather finally broke and we installed the rack onto my hitch, tightened it and it doesn't rattle. When I finally used the rack and put my bike on, it did sway a little but at 50 mph I was very happy with it. The trailer comes out just enough away from my car that I do not have to fold completely out and I can open my trunk with no issues. I am very happy with my purchase and had a great customer experience with Dan. Would highly recommend ordering from them to anyone.
# 4
RockyMounts MonoRail Solo Bike Rack for 1 Bike - 1-1/4" and 2" Hitches - Wheel Mount
I just finished installing this rack on my 2017 Subaru Outback. I've been researching platform racks for about 2 months now, and the most important things to me (other than a reasonable price) were no frame contact, ease of getting the bike on and off the rack, not too heavy for me to take it off the car, and enough clearance in the back for me to close my garage door. This rack is perfect for me. And I like that it's expandable to two bikes if I want to do that down the line. It came very well packaged. I am a single gal and not handy AT ALL, but I was able to do the installation with no problem. I did put my bike on the rack and took a short test ride, it was very stable. Very solid well made product!
Feels solid, minimal wobbling. Easy to get bike on and off, and to access the trunk with the bike on. Like that it can be expanded to hold 2 bikes, and the relatively low cost. Used with a Curt hitch from this site on a 2017 Miata.
# 5
Swagman XC2 Bike Rack for 2 bikes - 1-1/4" and 2" Hitches - Frame Mount
It works great! Easy, quick, you know. One needs to screw in the hitch bolt, for some reason, before latching it. Other than that, it makes going bike riding way easier.
I like the overall design of this rack, but unfortunately after hauling a couple bikes around for a while the point where the crossbar connects has apparently rounded off so the rack swings back and forth. I've used rope to tie the ends of the rack to the car to stop this from getting worse, but it's inconvenient. Note: the hitch connection itself is good and solid, but the point where the crossbar connects to the bar coming from the hitch has gotten loose and there's no way that I can see to tighten it.
# 6
Kuat Transfer V2 Bike Rack for 1 Bike - 1-1/4" and 2" Hitches - Wheel Mount
This is a solid product. Easy to assemble and simple to operate. A couple of issues make it less than ideal. First, because it is built to fit 1 1/4 and 2" hitches, the hitch pin holes do not line up correctly in a standard 2" trailer hitch. This means that you cannot use a 5/8" hitch pin. You can use the smaller pin, but you get the kind of fit you would expect -- it's loose and it rattles. If the cam system fails, the smaller hitch pin isn't going to help much. This is a huge design flaw in my opinion. Note that if you order the hitch pin lock that they say you need for this particular rack (HL2), it comes with a 5/8" pin that won't fit. Just dumb. My rack didn't come with the cable, so I contacted etrailer and after alot of back and forth, they said they would reach out to Kuat. That was a month ago. There is not a cap to snap over the cable lock, so when the rack is folded in the upright position, water leaks into the hollow bar behind the lock. It will sit in there forever unless you pull the rack and turn it upside down. I put a piece of duct tape over it -- the lock is no use to me since etrailer and Kuat can't seem to provide me with the missing cable.
The rack is great for a senior single. Lightweight to install into hitch and seems pretty sturdy. However the directions for assembly need help. 1.The Tire Hook Arm Assy and Arm Kunckle and Arm Installation: The pictures show assembling the Hook Arm and Arm Knuckle in one way. And Installing the Arm show the cutout of the Arm Knuckle for the screw another way. I think the 2 diagrams don't agree with each other as far as which side of the rack the arm is installed on. It added more time for assembly. 2. In the Hitch Shank Assembly, the holes for slipping in the bolt were not lined up - at all. Tried to wiggle, somewhat force it - no success. I finally figured out that the plastic wrap that was put into place to hold the Foot Pivot lever at a certain tension - wasn't really holding it at all. Once I pressed on the Foot Pivot tension lever, the holes could be aligned for an easy insertion of the bolt. I hope this helps
# 7
RockyMounts BackStage Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount
We love our RockyMounts BackStage Bike Rack. The fact that it can hold our two e-bikes and swings out for rear door access makes it perfect for vanlife. Service and communication from etrailer is outstanading!
etrailer.com asked me for a review about 1 week after it arrived. A better review would be in about 6-12 months after delivery to allow me time to use and experience the rack. Disclosure: my review is just for the assembly and install. Assembly is not easy. I needed to go to the internet and look at photos. The instructions lack detail. So only 4 stars for assembly instructions. It seems like a good design. The included locks seem cheap - like why bother including. The hitch pin design seems to tighten down the rack so there should be minimal rattle and movement. The rack sits up relatively high, so it would be safer to lift heavier e-bikes with two people or use some type of field engineered ramp. Wish it was made in the US and I wish the country of original was fully disclosed in the etrailer.com description. Perhaps it is disclosed but I learned it was from china after it was delivered.
# 8
Saris SuperClamp EX Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Wheel Mount
At the age of 70, I needed a “friendlier” mounting and bike access rack. A platform rack seemed to be the solution. I had one caveat. My Subaru Forester had a 1and 1/4” receiver (with a non-standard 3/4” length mounting hole). My Volvo had a tuck away 2” receiver. After some research I gravitated toward Thule only to find out they had no solution for my above conundrum. In fact their customer service offered no interest in solving my problem which others also must have had. More research…enter Saris! An American made company with an innovative solution. I quickly received my SuperClamp EX-2 from ETrailer along with excellent customer service support. The ease of constructing the unit for use and the obvious structural integrity was immediately apparent. My wife couldn’t believe how easy it was to use and to stow away on my garage wall after use. Thank you Saris and ETrailer for a wonderful product and experience. I guess American made is still alive and well. I highly recommend this product and the associated companies.
Purchased this bike rack last year and am very pleased with the stability of the rack. The straps and clamps secure the bike well to the rack. Some things that I learned: When attaching the rack onto your hitch, it helps to put a piece of tape on the rack (hitchtite) once you have lined up the holes. This will make it easier to find the exact location of the holes the next time that you want to use the rack. Finding the exact location allows you to smoothly hand tighten the bolt to the end of the hitch. At that point, just use a socket wrench to finish the tightening. When putting the bike on the rack, I loosely secure the clamps to the tires at first. This allows me to rotate the tires to find the right location in the wheel well for the straps to go around the spokes. I next secure the bike with the straps and then fininsh securing the clamps to the tires.
# 9
Softride Hang2 2-Bike Rack for 1-1/4" and 2" Hitches - Tilting
The bike rack is made for bikes with no fender, our bikes have fenders and a rack over the back tire. We added some padding for the back tire so the rack doesn't get scratched, it works just fine our bikes are secure.
Nice to keep bike rims distant from the exhaust, which can damage carbon-fiber rims. But, IMHO over-designed......very heavy with thick-walled box channel sections. At least we know it won't structurally fail :)
# 10
Thule T2 Pro XTR Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount
T2 Pro bike rack was delivered in a very timely manner. The rack was as described, extremely easy to assemble and is super user friendly! Exactly what I was looking for so my wife can use it by herself. Thanks
Great product, great company to do business with. etrailer is the best. Friendly, helpful and they made sure the bike rack was shipped immediately and it was delivered on time.
# 11
Hollywood Racks Trail Rider Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Frame Mount
Overall the hitch works great sturdy heavy duty easy to load. The only difficulty was getting a receiver mounted on our little Honda Civic that took a mechanic! This hitch is much better than the kind we used to use strapping on the back of the car much more secure.
I was impressed with this bike rack from the minute I unpacked it. The assembly was simple & straight forward. I looked at quite a few bike racks & for the price point this product was hard to beat. It is well designed & the keyhole pins make it easy to remove & fold up when not carrying the bikes. The locking hitch pin & locking frame bars are convenient and fairly secure. I will add my cable lock to make the bikes even a little more tamper proof. So far I’m very happy with this his purchase. Now the test of time!
# 12
Swagman E-Spec Bike Rack for 2 Electric Bikes - 2" Hitches - Frame Mount
I have pulled my 33’ 5th wheel around 400 miles since I installed my Swagman E-Spec bike rack with a Rad Mini and a Rad expand E-bike on board and have had absolutely no problems. The bikes are held firmly and safely in place without shake or excessive vibration. I have had friends follow closely behind me just to verify the ride and they are equally impressed. This bike rack makes carrying two E-bikes effortless. I can load and unload the bikes by myself without any problem and the “keyed alike” feature make all the locking components quick and easy to access. etrailer delivered without any hassle and their helpfulness in recommending the 4”+ tire adapters was the ticket to making my rack fit one of my bikes.
I was worried about a rear bumper bike rack for my 2 Lectric bikes bouncing too much but after traveling 2,000 miles, we didn't have any trouble. The Swagman E-spec from etrailer bike rack was made specifically for my RV and attaches to the hitch that is rated at 300 lbs. The bike rack locks the bikes into the rack and I had a cover from [online] to protect the bikes from the elements. Loading and unloading is very easy. Prior to the bike rack, we had to fold the bikes in half and put them in a 80 gallon plastic tub and muscle them into the living room between the slides and that was a horrible experience having to lift them into and out of the RV. The supply chain pandemic issue took place and delayed the arrival by 6 months but worth the wait.
# 13
Yakima RidgeBack Bike Rack for 4 Bikes - 1-1/4" and 2" Hitches - Tilting
Check out my other review on the hidden hitch for a 2015 BMW 4 Series for the majority of the review, but this thing is great. Easy setup and install, does all the things it's supposed to do. Mounting and removing bikes is a snap with the included clips (big difference from some of the cheaper variants with nylon ratchet straps). Fits very snugly in my 2" receiver, and pretty solid on the highway and over bumpy roads.
First trip with 3 bikes. Nary a wobble. The anti-sway strips appear to make a big difference.
What our customers are saying:
"Sent out an e-mail to you earlier this week asking which hitch woudld be the best choice for installing on a 2000 Venture van for hauling a bike rack with two bikes. You suggested the one that would be easiest to install..received in a matter of days..installation went great ..very well thought out instructions. Everything went smooothly and the hitch is up nice and snug..doesn't stick out..looks great."