Trailer Brake Controller Specs:
Features:
...without the knob lighting up. The knob will stay blue longer as the calibration process gets closer to being done. When the display turns solid blue, initial calibration is complete. The unit will remain...
Installation Notes:
You need item ETBC7 ($128.85) to install your controller.
You may also need a 4-Flat connector to complete your wiring.
More Information >Code: C51170-C51515
Trailer Brake Controller Specs:
Features:
...so you can get your settings just right. To switch between modes, press the control button in the center of the knob. Each mode has its own distinct LED display with several different colors...
Installation Notes:
You need item ETBC7 ($128.85) to install your controller.
You may also need a 4-Flat connector to complete your wiring.
More Information >Code: C51170-C32FV
Trailer Brake Controller Specs:
Features:
...so you can get your settings just right. To switch between modes, press the control button in the center of the knob. Each mode has its own distinct LED display with several different colors...
Installation Notes:
You may also need a 4-Flat connector to complete your wiring.
More Information >Trailer Brake Controller Specs:
Features:
This proportional brake controller automatically syncs to your vehicle's computer network for smooth, precise braking. Low-speed brake adjustment gives you 2 settings for different speeds. Plug-and-play controller mounts in any direction.
Installation Notes:
You need item ETBC7 ($128.85) to install your controller.
You may also need a 4-Flat connector to complete your wiring.
More Information >Trailer Brake Controller Specs:
Features:
Power output and braking aggressiveness can be easily adjusted with built-in buttons on this time-delayed brake controller. Includes digital display and manual override. Activates brakes with a preset intensity.
Installation Notes:
You need item ETBC7 ($128.85) to install your controller.
You may also need a 4-Flat connector to complete your wiring.
More Information >Trailer Brake Controller Specs:
Features:
...If there is no trailer connected, the unit will still calibrate, just without the knob lighting up. The knob will stay blue longer as the calibration process gets closer to being done. When the display turns solid blue...
Installation Notes:
You need item ETBC7 ($128.85) to install your controller.
You may also need a 4-Flat connector to complete your wiring.
More Information >Trailer Brake Controller Specs:
Features:
...on front of unit shows you your braking status Green light indicates that brakes are connected Color changes to orange and then to red as the power output increases Slide-bar manual override is within easy...
Installation Notes:
You need item ETBC7 ($128.85) to install your controller.
You may also need a 4-Flat connector to complete your wiring.
More Information >Videos
for Trailer Brake Controller
Help Articles
for Trailer Brake Controller
Expert Answers
for Trailer Brake Controller
While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the…
view full answer...The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.
view full answer...If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…
view full answer...A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…
view full answer...I&…
view full answer...I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your…
view full answer...The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…
view full answer...The number you provided,…
view full answer...For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…
view full answer...To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…
view full answer...The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…
view full answer...I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…
view full answer...