2017 Jayco Redhawk Motorhome Brake Controller

Features:

Mount the control knob of this proportional brake controller on your dash for a factory look, and install the main unit out of sight behind the dash with the included wiring harness. Control your braking power with the turn of a dial.

Installation Notes:

Vehicles with the 7-Way tow package have the blue output brake wire already ran from the back to the front. It is located under the dash near the emergency brake pedal.

If your vehicle has a round plug with a cap inside the driver's side frame rail instead of a bundle of wires in the jack storage compartment, use part # 30955.

Some models will require a wiring kit to run wire to the battery. This may require drilling a hole in the firewall to run the wire. You may use kit 5506 which includes 20, 30, and 40 amp breakers.

Tech Tip:

Some models will have the connection wiring taped and tucked under the driver side floor mat up towards the firewall.

Features:

Mount the control knob of this proportional brake controller on your dash for a factory look, and install the main unit out of sight behind the dash with the included wiring harness. Control your braking power with the turn of a dial.

Installation Notes:

You need item ETBC7 ($129.35) to install your controller.

You may also need a 4-Flat connector to complete your wiring.

Tech Tip:

Some models will have the connection wiring taped and tucked under the driver side floor mat up towards the firewall.

Features:

Mount the control knob of this proportional brake controller on your dash for a factory look, and install the main unit out of sight. The Elite's unique user-controlled mode gives you direct control of your braking for any weather or terrain.

Installation Notes:

Vehicles with the 7-Way tow package have the blue output brake wire already ran from the back to the front. It is located under the dash near the emergency brake pedal.

If your vehicle has a round plug with a cap inside the driver's side frame rail instead of a bundle of wires in the jack storage compartment, use part # 30955.

Some models will require a wiring kit to run wire to the battery. This may require drilling a hole in the firewall to run the wire. You may use kit 5506 which includes 20, 30, and 40 amp breakers.

Tech Tip:

Some models will have the connection wiring taped and tucked under the driver side floor mat up towards the firewall.

Features:

Mount the control knob of this proportional brake controller on your dash for a factory look, and install the main unit out of sight. The Elite's unique user-controlled mode gives you direct control of your braking for any weather or terrain.

Installation Notes:

You will also need item 37185 ($55.58) to complete your wiring.

The brake (blue) wire will need to be run from the brake controller back to the plug in the rear. The brake controller power and brake pedal wires are already run. A 12 volt hot lead from the battery may also need to be installed.

Features:

Mount the control knob of this proportional brake controller on your dash for a factory look, and install the main unit out of sight. The Elite's unique user-controlled mode gives you direct control of your braking for any weather or terrain.

Installation Notes:

You need item ETBC7 ($129.35) to install your controller.

You may also need a 4-Flat connector to complete your wiring.

Features:

Mount the control knob of this proportional brake controller on your dash for a factory look, and install the main unit out of sight. The Elite's unique user-controlled mode gives you direct control of your braking for any weather or terrain.

Installation Notes:

The brake controller can easily be installed with the included vehicle specific wiring adapter; no other parts are necessary.

Features:

Mount the control knob of this proportional brake controller on your dash for a factory look, and install the main unit out of sight behind the dash. Control your braking power with the turn of a dial, with manual override right at your fingertips.

Installation Notes:

The brake controller can easily be installed with the included vehicle specific wiring adapter; no other parts are necessary.

Features:

Mount the control knob of this proportional brake controller on your dash for a factory look, and install the main unit out of sight behind the dash. Control your braking power with the turn of a dial, with manual override right at your fingertips.

Installation Notes:

You will also need item 37185 ($55.58) to complete your wiring.

The brake (blue) wire will need to be run from the brake controller back to the plug in the rear. The brake controller power and brake pedal wires are already run. A 12 volt hot lead from the battery may also need to be installed.