We do carry the 33" Ark Stabilizer Jack that you are looking for with part # ARK77FR.
I was able to track down a few drawings that you should find helpful. These are for the 30" # ARK94FR and the 24" # ARK34FR Stabilizer jacks. I'm afraid we don't have a drawing for the 33" jack. view full answer...
The difference between the prices of the JR Products Automatic Changeover LP Gas Regulators and Camco Automatic Changeover 2-Stage Propane Regulators are in the BTU per hour, which as you correctly noted, is important information.
The JR Products Automatic Changeover RV LP Gas Regulator # 37207-30395 is rated for 345,000 BTU per hour for the Service Cylinder and 260,000 BTU per hour for the reserve cylinder.
The JR Products Compact Low Pressure 2-Stage Automatic Changeover RV LP Gas Regulator... view full answer...
I do have a potential option for you, but unfortunately we do not offer an air bag kit for your 2023 Chevrolet Silverado 1500 High Country Duramax 3.0L 4x4 with adaptive ride control suspension. We do have the # F2609 kit from firestone which does fit trucks with the adaptive ride control, but it will not fit Diesel models.
We would have to go in a different direction to enhance the suspension on your truck. Your best bet will be a RoadActive Suspension Custom Leaf Spring Enhancement... view full answer...
Yes, you can swap out your cap sensors for internal sensors and they will work with your current TST-507-RV-4 system. We offer the internal sensors individually with part # TST-507-INT-S1. Definitely a good idea if you don't want to have to worry about a sensor going missing. The internal batteries usually last at least 5 years. view full answer...
We have spoken to Fan-Tastic Vent about this issue in the past, and they have confirmed that there are no replacement remotes available for the 6500 model as it's no longer in production. So if you want to still use your existing fan but also wanted a remote, they said what you can use is the Fan-Tastic Vent 7350 Series Upgrade Kit # FV807359.
However, this is similar to getting a brand-new vent, so you can go that route, with a number of different options. For a powered lift with a remote... view full answer...
We definitely have a solution for you that will allow you to carry your two bikes though not the exact adapter you are asking about that already has a ball mount. The first option is to use a dual hitch adapter which does have the needed clearance between the top and bottom receivers, though you do need to ensure you get the one that has the correct rise or drop.
For that you can use the Roadmaster Dual Hitch Receiver Adapter, 6" Drop/Rise # RM-077-6, 8" Drop/Rise # RM-077-8 or 10" Drop/Rise... view full answer...
Yes, the Blue Ox Patriot BRK2012 does have a built in battery backup. So if the vehicles battery starts to go low, you have a bit of reserve backup in the brake unit itself.
Now the BRK2012 is no longer available, the new version is BRK2022. Our part number is # BLU37TR. The new version does not have an internal battery. So if you lose power it will not function. It does have a built in superconductor that will activate brakes if brakeaway occurs, and will keep the brakes activated for... view full answer...
The Replacement Standard Dual Rack Repair Kit for Lippert RV In-Wall Slide-Outs - Fixed Side, # LC84FR is the left side of the slide-out as looking at it, facing it, from the outside. The float side, # LC26VR, will of course be the right side as facing the slide-out from the outside.
The "Fixed" assembly will have the installation alignment flange of the shipping angle on
the right-hand side of the assembly, when looking at the "S" track on the gear rack. The "Fixed" assembly has
an... view full answer...
IMGL when referencing the Kwikee steps stands for Integrated Motor Gear Box Linkage. In October of 2004, Kwikee Steps made by Lippert changed their system from the separate parts to the integrated system. Prior to this there was a cast linkage separate from the gear box and these steps are from 1999-Oct 2004 referred to as Pre-IMGL.
They kept replacement parts but started making the Lippert Components Kwikee Step Motor Conversion/Upgrade Kit # LC379145 to eventually transfer over completely.
I've... view full answer...
I spoke with the manufacturer, Command Electronics, about the 12V RV LED Puck Light # CE68ZR and found that it has a warm white - 3,500 kelvin rating. view full answer...
The Trailer Valet XL, part # TVXL2 with 2 inch ball and the # TVXL25 with the 2-5/16 inch ball are meant for use on level surfaces only, they wouldn't work well on the slope you describe..
Actually, I have a much less expensive and easier to use alternative. I'd install a front mounted receiver like # C31073; the front hitch will allow you to easily put that camper right where you want it, slope or no slope, every time. view full answer...
I have attached a page from the installation instructions for the Extang Solid Fold 2.0 Hard Tonneau Cover # EX83475-62.
The page shows the parts that should be used with the rear panel you said blew off. You can look at the page to make sure all of the parts shown are still with the rear panel. view full answer...
The general reason a battery needs to be disconnected for flat towing is because there are certain functions that need to be disabled to prevent your vehicle's battery from draining. You wouldn't want to get to your destination and unhook and then have a dead battery and not be able to move your vehicle. You should always follow your vehicle's manual to the letter to prevent damage to your vehicle.
If you want to install a switch to make disconnecting and reconnecting the battery simple... view full answer...
Yes, you can keep your oil bath hubs and use the Kodiak disc brakes; you mentioned a salt water environment and stainless steel brakes so you have two options, with the all-stainless steel being the best in terms of corrosion resistance, as you can see by the salt spray ratings of each:
- 300- to 400-Hour Salt-Spray Rating: Dacromet and Stainless Steel: Kodiak Disc Brake Kit # K2R35DS
- 1,000-Hour Salt-Spray Rating: Stainless Steel: Kodiak Disc Brake Kit # K2R35S
In order to be sure... view full answer...
To initially adjust the brakes, you will need to raise the trailer and secure it on adequate capacity jack stands. Check that the wheel and drum rotate freely. Do not lift or support trailer on any part of the axle or the suspension system. Remove the adjusting hole cover from the adjusting slot on the bottom of the brake backing plate. With a screwdriver or standard adjusting tool like part # W80630, rotate the starwheel of the adjuster assembly to expand the brake shoes. Adjust the brake... view full answer...
The Electric Jack w/ Footplate and 7-Way Plug # EJ-3527-BBX uses a 7-way RV-style plug. I have included a diagram that shows the pin-out for RV style 7-way plugs. This will show you what each pin does. I have also listed the functions below and linked to a help article that covers this.
Green: Tail/running lights
Yellow: Reverse Lights
Brown: Right turn/brake light
White: Ground wire
Blue: Brake controller output
Black: Battery hot lead
Red: Left turn/brake light view full answer...
I have a solution for you, it is a smaller fan unit but we have an item that will function in the way you are looking for. The MaxxFan Mini Plus Manual RV Roof Vent, # MA00-03851 that you linked to needs a fairly stable power supply of 12 VDC and draws slightly less than 2 amps to operate. Wiring directly to solar panel will not support this as the power will fluctuate greatly and eventually damage the electronics in the in the fan. To operate, you need a stable 12 VDC power supply from... view full answer...
I have a solution for your clearance issue, but the Lippert Jack # LC285318 cannot be rotated. You can get a bit more clearance by using a longer ball mount like this extra long ball mount # D-26. It measures 12-5/8 inches from the hitch pin hole to the ball hole. This will give you more clearance. You could always rotate the whole jack, but you will have to drill some holes and may need to use different hardware depending on your trailer. Obviously you will have the switch and light facing... view full answer...
Trailer Brakes are not required on most trailers under 3,000 lbs unless otherwise stated by the local authorities. This should not be an issue with safety behind your 2014 Subaru Outback, but you can add them if desired. I would just need you to pull a hub and let me know the number on the grease seal and the face of the 2 bearings in that hub. With that info I can get you the parts needed for the upgrade.
The bigger issue with a trailer this size and weight is sway caused by wind... view full answer...
Go To Results