Hello Robert, thanks for reaching out. The Roadmaster Comfort Ride is a great choice for a suspension upgrade. This system is compatible with the MORryde X-Factor Crossmembers, so you can add those to all 3 hangers if you wish.
One thing I would do is look at your hangers and make sure they are standard hangers welded to the frame. Make sure there are no obstructions like wiring or plumbing that would get in the way. You can do the MORryde X-Factor Crossmember # MR33WR, or you can do... view full answer...
Hello Nathan,
Great question. There are 2 key factors with finding the right Gen-Y Gooseneck, the pin box number, and the pin weight (tongue weight). I was able to look up the GVWR of your 2022 GD Reflection 367BHS which is 14,995 lbs. They have a special formula for getting you into the right Gooseneck, if you take the GVWR and times it by 0.22 you get 3,298.9, if you look at the chart that I attached that puts you into the 4,500 pound executive pin weight capacity.
So now that we have... view full answer...
Hey Joe, welcome back! With a 35" wheelbase the MORryde AllTrek 4000 Equalizers for Tandem Axle Trailers # MR29DR is the correct fit. I verified your Reflection has 6k axles on the Grand Design parts site so the # APUBR-8 is also correct and so is the capacity on the # e88SR. Did you account for the leaf springs flattening out over time? Assuming you did, these will work as a replacement with the 26" eye to eye measurement.
The shackle strap length isn't listed on the parts site so you... view full answer...
Hey Bruce, thanks for reaching out!
It sounds like you're looking for the Replacement Small Door Bin for Furrion Arctic 10 cu ft 12-Volt Built-In RV Refrigerators # FR57VD.
If you have a different Furrion fridge then I recommend checking with your local appliance store to see if they have something that might work as Furrion doesn't have any other fridge door shelf replacements available. view full answer...
Hey Patti, thanks for reaching out. The Swagman E-Spec Pro Bike Rack # S45SR is a solid option for this. It can hold two bikes weighing up to 70 lbs apiece on a 5th wheel, and it does not have a minimum tongue weight capacity limitation like the Hollywood rack you mentioned. As long as the weight of the bikes plus the rack is under 300 lbs you'll be good to go there.
If you need something with an 80 lb per bike rating, we do have the Hollywood Racks Sport Rider SE # HLY84FR. This is rated... view full answer...
Hey Scott, thanks for reaching out, and nice camper! We can definitely provide the bushings and wet bolts for it. The best, most cost-effective way to do this will be with a full kit that comes with shackles, wet bolts and bronze bushings. We'll just need to make sure we get you the right size shackles (should be either 2-1/4" or 3-1/8" long) so please check that and select from the following:
- MORryde Suspension Upgrade Kit for Tandem Axle Trailers - 2-1/4" Long Shackle Straps # MR46ZR
-... view full answer...
Hey Mitch, thanks for reaching out!
The Progressive Dynamics 9300 Series RV Converter Charger # PD79RR can be used to charge 2 lithium batteries. I'm not sure what came on your 2017 Grand Design, but this measures 8" long x 9" wide x 3-5/8" deep, so you can compare this to the space that you have.
Does this seem like it will work for you? view full answer...
Hey Steven, since we know you have a 6k rated axle the correct bearing kit that includes a grease seal would be the part # BK3-100. Did you have bearing issues or are you looking for a backup set to keep around just in case? view full answer...
Hey Thomas, congrats on your new trailer. You might have to play around with the different positioning of the pivot arms once you get the trailer home. There's no of knowing exactly what position you'll need without knowing the pin box location, the width of trailer, and the shape of the trailer nose in relation to how tall your truck is.
I attached a screenshot from the instructions below. I recommend setting the pivot arms at the highest with the most clearance, top right. This will... view full answer...
Hello Phillip, thanks for reaching out. Trailer rims like the Aluminum Eagle Trailer Wheel # LH48VR do not have a PSI rating. They can handle the PSI of any 16" trailer tire. The actual PSI rating is determined by the valve stem, which for the # LH48VR wheel is a rubber valve stem rated for up to 80 PSI.
If your tires go higher than 80 PSI, replace the rubber valve stems with the metal valve stem part # AM20906 which are rated for over 200 PSI. view full answer...
Hey John, welcome back and thanks for all the information! The Lionshead wheels like the Aluminum Liger item # LH98VR you were looking at, don't have a max PSI rating but the valve stems that typically come with them item # AM20904 top out at 80 psi.
I recommend checking your valve stems and if necessary replacing them with the Americana Metal, Bolt-In Valve Stem item # AM20906. These are rated for over 200 PSI so they will work with your 110 PSI tires.
If you have any additional questions,... view full answer...
Hey Craig! Is this a Lippert Ground Control system? Is the part actually 304136? I asked Lippert and they said they don't have anything under 304135. If it is the 304136 the correct replacement is the Replacement Control Module for Lippert Ground Control 3.0 Electric Leveling System # LC304136. view full answer...
Hello Mark; is this a 2019 Grand Design Reflection? Assuming it is, the lowest listed GVWR is 8,995 lbs on the 220RK. The unloaded weight is 6,695 lbs but that isn't what determines fitment, and you're going to be heavier than that no matter what. Is that what you have? Also, do you have a Lippert Turning Point right now? If you do, then the Gen-Y Hitch Shock Absorbing 5th Wheel to Gooseneck Pin Box # GY48GR will actually work for you.
If you have a different model, or different pin box... view full answer...
Hello Joseph, thanks for reaching out. We do have a vent cover that can replace your MaxxAir 00-933067 smoked lid. For that I recommend the following:
- MaxxAir II RV and Trailer Roof Vent Cover w/ EZClip - Smoke # MA26JR
This is the same smoke color lid you have now. It comes with brackets and ez-clips used to attaching the lid. It will work with really any MaxxAir vent made after 2015 so this will definitely be your best bet.
What space will the lid serve? Bedroom or bathroom? view full answer...
Hey Scott! Yes, the Dexter Grease Seal for 12" x 2" Hubs - 2.25" ID - 3.376" OD # DX72UR is the same as the 010-036-00. This is a pair of seals so it is under a different part number, technically Dexter K71-305-00. They have the same inner and outer diameter as the # 10-36 which is the same as Dexter 010-036-00 so they will work as a replacement.
Are you getting your Reflection ready for spring/summer? Any big trips coming up? If you need anything else let me know in the comments below. view full answer...
Hey Dwayne, the pendent on the Progressive Dynamics panel # PD79RR that you have is designed to provide you with a visual indicator of the converter's battery charging status and allows for manual control over the four charging modes Boost, Normal, Storage, and Desulfation. What type of battery are you charging? view full answer...
No, I am sorry Herb we do not carry replacement windows. It does look like Lippert has those parts available on their website though. view full answer...
Hey Kent, we have the part # TLA8004 for a 4 step or the part # TLA8006 for a 6 step Torklift Glowstep that has a base that is 27-1/2 inches wide. Do you know how many steps you are wanting or how tall your threshold is from the ground? view full answer...
Hello Timothy, thanks for reaching out. What part are you needing exactly? Are you needing the wheel center cap? Or are you needing the grease cap that goes on your hub. I see you have a 5,200 lb axle an typically this would use a 2.44" grease cap like part # RG04-080.
If there is something different you are needing just let me know. view full answer...
Go To Results