That is correct.
To install the Curt Trailer Hitch Receiver # C29UR on your 2018 Chrysler Pacifica Hybrid you will need to remove two the exhaust hangers from the rubber isolators, and support the exhaust to make sure it does not get damaged. Next you will remove the heat shield you mentioned, and will need to trim it according to the included diagram.
Once the hitch is in place, you will reinstall the heat shield, and the reinstall the exhaust into the rubber isolators. You will also... view full answer...
I attached an install picture for the Draw Tite hitch part # 76046-SK that you referenced on a similar 2020 Chrysler Pacifica for you to check out. It's not a hybrid model in the picture but it would look the same on your hybrid model. view full answer...
I spoke with Progressive Dynamics and they informed me that you cannot replace just the converter section of your 8735P and you would need a new panel, the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger part # PD4045KA to be able to charge a lithium battery.
The Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger now comes with a lithium switch. view full answer...
There is a small difference in installing the etrailer.com Trailer Hitch Receiver part # e98903 on a Hybrid compared to a non-hybrid 2021 Chrysler Pacifica. There is an emissions canister on the driver side frame rail that needs to be relocated temporarily to install the hitch.
If you check out the attached install instructions link for this hitch on this page on step 5 you'll see this outlined. view full answer...
The installation of the etrailer.com Trailer Hitch Receiver # e98903 will be the same as the Curt Trailer Hitch Receiver # C13383 for your 2019 Chrysler Pacifica Hybrid and I have attached the installation instructions of the Curt hitch for you so you can see exactly how to install the hitch on your Pacifica (the only difference between the two hitches is the matte black powder coat finish of the etrailer.com hitch compared to the gloss black powder coat finish of the Curt hitch).
The... view full answer...
The etrailer.com hitch part # e98903 is a confirmed fit for your 2020 Chrysler Pacifica Hybrid and does have a couple extra steps for the hybrid models. There's an emissions canister that needs to be relocated temporarily when installing the hitch and also there are some holes on the driver side frame rail that need to be enlarged. I attached a diagram that shows this as well. view full answer...
I have good news for you - since you have a factory 7-way in your 2020 Chrysler Pacifica you have a very simple "installation" which will require nothing more than plugging a brake controller wiring adapter into the port under the dash of your Pacifica and then plugging the brake controller into that adapter (essentially, you can think of the adapter as like an extension cord for the brake controller).
I really like the Tekonsha Prodigy P2 Trailer Brake Controller # 90885 because it is... view full answer...
I confirmed with Thule that you will need to use setting 10 for the FitDial on your Thule Gateway Pro 2 # TH88VR when mounted on your 2017 Chrysler Pacifica. view full answer...
That is correct, you will want to install the top straps of the Yakima FullBack 3 Bike Rack # Y02633 using the anchor method for your 2017 Chrysler Pacifica. I've installed this rack that way a few times and I found it easier to remove the hooked strap, feed the strap through the hook as outlined in the instructions (see attached), and then feed the strap up through the crack at the top of your hatch instead of trying to push the hook down from outside of the vehicle.
I actually had the... view full answer...
We have both 1-1/4-inch Class II and 2-inch Class III hitches confirmed to fit the 2018 Chrysler Pacifica Hybrid that are shown on the linked page. Both Class II hitch # C12180 and Class III hitch # C13383 will require temporary removal and re-installation of the carbon canister on your hybrid's driver-side frame rail. It will be reinstalled using hardware supplied with the hitch.
Instructions for both hitches are linked for your reference. view full answer...
The Curt Trailer Hitch Receiver part # C13383 is a fit for your 2019 Chrysler Pacifica and the trailer hitch I recommend for you because it has a 2" receiver tube opening and is a custom fit so no drilling is required. The hands free liftgate sensor I believe you are referring to will still work just fine with this hitch installed however, you will need to place your foot on either side of the receiver tube opening in order to activate it. This will be the case for all of the trailer hitch... view full answer...
The cold side of a brake light switch is used as the trigger signal to activate a trailer brake controller like the Prodigy P2 # 90885. The controller installation kit you purchased, part # ETBC7, includes a probe-style circuit tester that allows you to determine which of the wires at the brake light switch is connected the to cold side of the switch. The correct vehicle wire to connect to the RED wire on the controller is the one that goes hot ONLY when the brake pedal is pressed, and... view full answer...
The issue you are having with the # e98903 hitch holes not lining up correctly on your 2018 Chrysler Pacifica is likely due to the hitch being bent. Sometimes a hitch gets slightly bent during shipping, which may result in misalignment during installation.
I would inspect the hitch and make sure there are no cracks, chipped paint, or stress marks. These are signs that the hitch may have flexed enough to be considered unsafe and should be replaced. Assuming that is not the case, the trailer... view full answer...
You're on the right track; this is the correct adapter, and the best place to look for the reverse light circuit when installing the Tow Ready 4 Pole to 5 Pole Trailer Wiring Adapter # 20036 is on the tail light assemblies on your 2018 Chrysler Pacifica. When installing this adapter, you may need to have a friend activate each function and test the wires using a circuit tester like the # PTW2992 to get the correct wire to tap into. view full answer...
Installing a brake controller in your 2019 Chrysler Pacifica is going to depend on if you have the factory 7-way or no factory trailer wiring at all. If you do have the factory 7-way you can install a brake controller with just the correct wiring adapter. For example, the Tekonsha PowerTrac # 39523 brake controller requires just the Plug-In Wiring Adapter # TK93VR. You will plug in one part of the adapter to the controller and the other part to the port underneath your dash for a simple... view full answer...
The black wire on the # ETBC7 should be run to the battery. The 12V cigarette lighter is meant to be used for accessories. Running the wire to your battery ensures that you do not cause any damage to your vehicle wiring if something were to draw too much power.
I have attached an installation video below so you can see what the process is like. view full answer...
For the Curt hitch part # C13383 that you referenced you do have to enlarge holes on the driver side frame rail to fit the hitch on the hybrid models of the 2019 Chrysler Pacifica. I attached a picture that shows this. The picture on the left shows the square before picture and after you can see the shapes of the holes is a bit rounder.
The only holes that would ever need to be enlarged to install a trailer hitch would be on the vehicle. None of the hitches we offer will require you to... view full answer...
Good news! Installing a trailer hitch like the etrailer # e98903 on your 2020 Chrysler Pacifica Hybrid will not affect the operation of the hands free liftgate feature on your vehicle. You'll simply slowly kick your foot to either side of the hitch receiver to open the rear cargo hatch in the same manner that you normally would.
If you're going to be towing a trailer at all with your 2020 Pacifica Hybrid you'll need a wiring harness, ball mount and hitch ball to complete your towing setup.... view full answer...
It sounds like you are looking for the power wire connection point for the T-One Wiring Harness, # 118303, on your 2005 Chrysler Pacifica. We have a video detailing this installation on the 2005 model and you can see the power wire location behind the taillight and then a grommet on the driver side at 48 seconds into the video. view full answer...
The LED brightness in the control knob for the Redarc Tow-Pro Elite Trailer Brake Controller # RED44FR is not adjustable. However, the LED indicator brightness will reduce after you adjust the braking power or use the manual override. This is designed to be less intrusive on driver's vision at night. If you have the tow package on your 2020 Chrysler Pacifica you will also want the # RED77FR for installation.
If you are still concerned about the brightness of the control knob you may also... view full answer...
Go To Results