5" x 4-1/2" LED utility light produces a bright white light. Spot beam offers focused illumination at a distance. Black powder coat aluminum housing is rustproof. Impact-resistant lens. Pedestal mount with included hardware. 9 Diodes.
Features:
Specs:
Lumens are used to measure the amount of usable light that is put out by a light source. Raw lumens represent the number of lumens that the manufacturer claims the LEDs are capable of producing. It does not include the light's drive method or the amount of light lost from the lens or reflector. Effective lumens take these factors into account and represent the number of lumens that are actually produced by the complete light assembly, not just the amount of light that the diodes are capable of producing. This light has a 1,800 raw lumen capacity and produces 900 effective lumens.
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hey everyone. I'm Ellen here at etrailer.com today, we'll be taking a look at the OptiBrightt LED work light. This is going to be a handy item to have on your work truck, your ATV, UTV, or really anywhere that you need a little extra light, especially if you're going to be working at night or in low light situations in general. This is going to be a very heavy duty light. It's going to have an impact resistant lens and also a nice aluminum housing. So it's going to be resistant to rust and corrosion.
You can see those nice deep fins on the back. So it's going to help to dissipate any heat buildup. So it's going to make our LEDs last, that much longer. This is also IP 69K rated. And basically that means that it's up to the....
It's going to be up to stuff for being outside all the time, any rain or wind or sleet or anything it's not going to get in there.And also if you want to wash down your vehicle with a power washer or anything like that, it's not going to have any ingress of water or dust. So that IP 69 rating just means that it's been tested with high pressure, high temperature sprayers for at least three minutes in different directions and angles. So it's all sealed up nice and tight, and yoou shouldn't have anything to worry about there.This is an LED light as well. So we're not going to have to worry about changing out any bulbs, ever. There's no maintenance with this since there's no filaments that can burst on us or break apart.
So there you don't have to change out any bulbs. It's also going to be more energy efficient than our typical incandescent bulbs and lasts about 50 times longer than your typical incandescent. So a nice, rugged, long lasting light for us in. Just about any situation.I'm going to turn on my power source here. We can see how bright this light is.
So turn on pretty bright and see it's a nice spot beam. So it's going to be a really focused light and that'll work well for just spotting in the dark. I'm going to turn my lights in the studio out so you get a better idea of how bright that is. I'm going to pull this away from my table so you can see it's kind of a trapezoid shape once you get pulled away from it. So the effective lumen output for this is going to be 900 lumens, with a raw lumen output of 1800. Really that effective lumen is going to be what you want to go off of since that's more a realistic number of what it actually will do for you.But definitely a nice bright light, will have nine diodes total, and should last for a long time. As far as the power that this can work with, it's compatible with 12 volt DC and 24 volt DC systems. So it's pretty typical for any automotive application. As far as the size, give you some measurements here, it's about four and a half inches tall by about five inches wide and about roughly two and a half inches deep. If we include the stand in there it's about an inch and a half from the bottom of that stands the top of this housing. So that would put us at just about six inches tall overall.Does come with the hardware to mount this, it's just a little U bracket and a bolt and nut and washer going through the base there. So you can adjust the angle on that light and then you'll have a carriage bolt, a split washer, and a lock nut to mount this in place. I would suggest putting this carriage bolt in that little bracket before you put it on the light, just because there's not a lot of clearance there and you probably won't be able to get that bolt in place once that brackets on there. So just a little words of the wise.As far as the diameter of that bolt, it's just about three eighths of an inch maybe, just over a quarter inch in diameter, just to let you know how big a hole you would need to drill out or a hole that this would fit through. The head of the bolt. that's a carriage bolt so it's going to be capturbed by that L bracket so it shouldn't matter too much for you. But as far as the outside dimension here of our mounting hardware, it's about two and a quarter inch. And then the wire coming off of our light is just about 11 inches long.The power draw at 12.8 volts is 1.5 amps. And at 24 volts it's going to be 0.73 amps. There is a lifetime warranty on those LEDs. And that just about does it for our look at the OptiBright LED work light. If you need any other accessories for your vehicle, you can always turn to us here at etrailer.com. We've got a lot of information, a lot of options available to get you back out on the road and enjoying your vacation or enjoying your work, whatever you might be up to. Thanks for watching. We'll see you next time.
It installed but seems like great quali ty.
Works great.
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.