Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
7-1/2" x 3-1/4" Oval. Waterproof light with 22 diodes provides brake, tail, turn, and backup light functions. Red lens is set inside of clear lens. Mounts on surface of trailer with built-in flange. Accepts industry-standard plugs.
Features:
Specs:
The waterproof construction of this light makes it ideal for use on trailers that may be submerged, like a boat trailer. The housing and lens are sonically sealed together to create a single unit, which means that water will not get into the light and damage the diodes or circuit board.
Surface-mount trailer lights install using a flange or bracket with mounting holes. These lights lay flat against the trailer surface and only require a small, often pre-existing hole, for wiring. Mounting hardware is used to secure the light to the trailer.
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Ellen: Hey everyone. I'm Ellen here at etrailer.com and we're going to be taking a look at the fusion LED taillight. This is going to give you stop, turn, tail and also a reversible light or a reverse light so you can back up and see what's going on behind you. So it's going to give you a lot of options. You can wire it a couple of different ways to utilize all those functions or just some of them depending on your application. The nice thing about this is that it is an LED light and it's also submersible so you can use this on an enclosed trailer, on a marine trailer, on maybe something that's a little bit more off-road.
If you want to make sure that no water, dirt or dust is going to get in here and cause any issues, this should be a good option for you. Something that I also really like about LEDs, so there's nothing to replace with these. As long as the housing is undamaged, we shouldn't ever have to do anything with this light. There's no maintenance required like with an incandescent bulb.Over time, you're going to have to change out that bulb because the filament is going to go bad, so it just adds more stuff to do with that lighting. As long as everything stays good with this, shouldn't really have to do anything with it once you put it on there.
It's pretty easy to get installed. We'll have two plugs for the wiring. One of them is just going to be for that backup light or that reverse light. The other is going to be for our stop, turn and tail light signals. So if you don't want to have the reverse light, you don't have to hook it up, but if you do, you will need to get two plugs to utilize with this.It's pretty standard plugs that this uses.
One is going to be a three prong. That other backup light is going to be the two prong. You can find options for that wiring here at etrailer.com, it's going to be a related part on the product page here at etrailer so you can check those out and get them while you're here. But as far as how it's going to look, you can see the two plugs there. Again, three prong, two prong.
I'm going to hook them up to my system, so I've just got some of those plugs here. Should look something like these two guys. We're just going to match those up and plug them in. I've got power going to these, so as soon as I plug it in, you'll notice that light's coming on. Just get that seated in there. You can see that red ring going all the way around. That's going to be our running light circuit. It's going to provide a nice clear indication when our lights are turned on so other vehicles, other drivers can see us even in the rain or in the dark.Turn out the lights in the studio. You can see how bright that signal is. So if we turn on the input there, you can see if we hit the brakes and also hit our reverse signal, everything's on. So we have our red lights on in the center there as well as the white light at the end. Again, that's powered by that two prong plug. So I'm going to unplug that because I have everything kind of running together. So whenever you hit the brakes or you use your turn signal, normally it's going to look like that. So it will illuminate those red LEDs in the center, give you your signal there and then if you hook up your backup signal and I'm going to turn my lights on so you can see what's going on. If you hit the brakes there, we can have this running separately just depending on how you wire that up.So if I take the power off of that guy, well anyway, that gives you the basic idea of how this is going to work without taking forever to figure that out. So again, if you don't want to use that backup signal, you don't have to, it is going to be wired separately, but it gives you an easy way to separate out those wires. There is a little legend on the back of the light to help you remember which wire is which. So the top white is going to be our ground signal. That black wire is our tail light or our running light signal. The red wire is our stop and turns, our brakes and our turn signals. The brown wire is our reverse signal or the backup signal. And the second white wire is also a ground for that signal, so it makes it pretty easy to figure out which goes where.As far as the size, overall, it measures about seven and a half inches long from the outer edge of that bezel to the same spot on the other side. We flip it round the other way, it's about three and a quarter inch wide. The light itself is about six and three quarter inches long or just under six and a half inches long by two and a quarter, and it's an inch tall or an inch thick. The mounting holes will have four going all the way around that perimeter. The distance between them, center to center is about two and three quarter inches center to center and then about seven inches center to center. The holes are about an eighth, maybe three sixteenths in diameter. It does not come with any hardware, but if you pick up some three sixteenth or eighth inch bolts or screws, should work just fine for that.As far as the more detailed specs, it does have 22 diodes in total and it has a power draw at 12.8 volts for the stop and turn light signal of 0.37 amps. For the tail lights, it's going to be 0.2 amps. For the backup light, it's 0.242 amps. There is a lifetime warranty on those LEDs. It is DOT compliant and should be a great addition to your trailer to get that mounted up and have all of your turn signals in one light. I think this is a really nice looking light. That little red bezel looks really cool. It's kind of a glow light, almost kind of has a sort of futuristic retro look to it. So I think it looks pretty nice and again, since it is submersible, it should last you a long time. Well, I hope this video's been helpful in deciding if this light is the right one for you. Thanks for watching and we'll see you next time.
Average Customer Rating: 4.8 out of 5 stars (258 Customer Reviews)
7-1/2" x 3-1/4" Oval. Waterproof light with 22 diodes provides brake, tail, turn, and backup light functions. Red lens is set inside of clear lens. Mounts on surface of trailer with built-in flange. Accepts industry-standard plugs.These lights are great on my PU camper , a little over priced - probably as they are waterproof. Very bright back up and break/ turn lights . Running is more subdued, so as not to be mistaken for breaking
The lights are great, they are well made and are holding up very well. The LED's are bright, so far so good. My only issue with the lights was not being informed in advance that they wouldn't work without a wiring adapter and cutting up of my wiring harness. I probably would have bought the lights anyway but more informed purchasers are happy purchasers and finding the lights you just purchased wont work without an adapter, well not good.The problem wasn't with the lights it was with Etrailer.
Absolute garbage I had a custom built trailer with custom wiring and a lot of time and effort was put in to make sure that these lights did not fail I used aluminum rivets with nylon spacers fully soldered connectors with adhesive heat shrink and the lights still failed. Unfortunately I have not reached out to to see if they have warranty. But, unfortunately the money spent already to build a separate housing for these lights will cost me in the long run due to the fact I can now only run the similar light. Very unfortunate they have not tested these lights thoroughly enough.. do not recommend. Especially for salt water.
Brooke M.
3/18/2023
I am sorry to hear these lights failed you so easily. The good news is that there IS a warranty. I see that our customer service team is already working with you on this.
Awesome buying experience. Great looking trailer lights
Simple part that works as designed. Adds visibility to my black trailer when parked without the lights on. Also adds a slight bit of security against theft of the tail lights by covering the screw heads.
Good quality. Great illumination. Easy installation on the back of my truck camper
Added as auxiliary lighting to my 10' trailer. Mounted high up on the tailgate ramp for enhanced left/right turn visibility. Very much wanted the back-up light functionality for nighttime trailering.
I especially was impressed with customer support. No "21 questions," no hoops to jump through... they just solved my problem. They have earned my repeat business.
tail lights need to have better packaging, they where scratched and scuffed during shipping, lights where loose in package no wrapping at all.
Brooke M.
8/17/2022
Thank you for letting us know I have sent your information along to our customer service team and they will be reaching out to you.
Lights look like they will work great , Anouther instance of not fully reading description , As price is for individual light , had to order the second one as soon as I discovered my mistake .
Great service,
Great Products,
On time delivery
My new go to rear tail light company.
Thank you very much,
Milea Maspeth Queens New York.
Nice combination unit. And a good price for it.
Exactly what I was looking for, good quality and fast shipping!
The items arrived on time, and we’re exactly as described.
They look great!!!
Do you have a question about this Trailer Light?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Michael
4/27/2023
The lights are still working well. None of the LED’s have gone out, the lights are still very bright and I am still very satisfied with them. The wiring adapter I had to purchase to make the lights work is also working perfectly.