Fulton Bolt-Thru Swivel Marine Jack - Weld On - Sidewind - 10" Lift - 1,500 lbs

Ask the Experts about this Fulton Trailer Jack

• Handle Hits Boat Using Fulton XLT Bolt-Thru Swivel Trailer Jack F141132
  The only trailer jack that will work with your existing mounting bracket and not contact the boat with a full rotation of the handle is the Fulton Bolt-Thru Swivel Marine Jack part # F1411300301. I understand this does not have the sharkskin coating you are after but the z-max finish is just as durable and will be no problem for salt or fresh water. The problem with the Fulton XLT Bolt-Thru Swivel Trailer Jack part # F141132 is that the mounting bracket is located too far down on the tube...
  view full answer...
• Replacement for Fulton Magnum Series Jack on Boat Trailer
  The Fulton Bolt-Thru Swivel Marine Jack # F1411300301 will definitely work for you as a replacement for the current Fulton Magnum Series jack you have, as it will mount to the bracket already on your trailer, as that bracket will be the Jack Mounting Bracket for Fulton Marine Jack # P9012-00. This Fulton jack has a 1,500 lb capacity, and while I completely understand thinking that the higher capacity of the jack, the better, that just isn't the case, because trailer jacks nowadays have...
  view full answer...
• Replacing a Shelby 1,000 lbs Trailer Jack With a Similar Fulton Jack
  Since we do not have a Shelby jack mounting bracket that goes to the discontinued Shelby Jack # 5876A8, I have no way to confirm whether or not a Fulton jack will fit it. With that being said, the Fulton Bolt-Thru Swivel Marine Jack # F1411300301 is almost identical to the Shelby Jack # 5876A8 that was referenced. It has a 10 inch lift, is rated for 1,500 lbs, has an extended bracket height of 24-3/4 inches, and will mount to a 3 x 5 trailer frame. The Fulton Mounting Bracket that...
  view full answer...
• Replacement Fulton Bolt-Thru Pull Pin Tongue Jack for Triton Boat Trailer
  The 1500-lb-rated Fulton Bolt-Thru Swivel Marine Jack # F1411300301 is a great choice to replace your Triton trailer's jack. You just want to make sure your jack mounting plate looks like part # P9012-00 which provides a bolt-thru installation. If you need a replacement bolt kit use part # F0933325S00.
  view full answer...
• Will Fulton 1500 lb Bolt-Thru Swivel Jack Fit the Same Mount on Older Fulton Swivel jack
  Fulton bolt-through trailer jack # F1411300301 is the only Fulton jack that mounts using that 1 center bolt. Since your old jack was a Fulton it must either be this same jack or an earlier model but they use the same mount. The mount in question and what is on your trailer is # P9012-00. On the off chance that the mount you have is slightly different then you could always use this one as a replacement. The 4 holes are 3 inches apart on center. The bolt that it uses is a 1/2 inch bolt,...
  view full answer...
• Swivel Trailer Jack with a Wheel for a 2007 Viking Pop-up Camper
  The Fulton jack, # F1411300301, is a weld-on application and you will need mounting bracket # P9012-00. The mounting bracket is the part that gets welded to the trailer frame. Any welding should be done by a qualified professional welder. It can be mounted on the trailer near the coupler (where the tongue weight is lowest) anywhere you have space. A 1500 pound capacity can handle a tongue weight of 1500 pounds. It is very unlikely that any pop-up camper will have a tongue weight that...
  view full answer...
• Replacement Jack Recommendation for Shelby that Bolts to Welded Swivel Mounting Bracket
  We have options that will work for you, but since we no longer carry Shelby jacks we don't have anything that will bolt directly to the mounting plate on your trailer frame. The most similar option is the Fulton Swivel Jack # F1411300301 which has a 10 inch lift and is rated for 1,500 lbs. The mounting bracket you'd need for this jack would then be the part # P9012-00.
  view full answer...
• Replacement Fulton Snap-Ring Swivel Jack for 2000 MFI Boat Trailer
  The Fulton Bolt-Thru Swivel Marine Jack # F1411300301 installs on a weld-on mount like # P9012-00 but for a snap-ring pipe mount you'll want to use a jack like # FTJ120W0301. This jack offers a 1200-lb lift capacity and a 6-inch wheel. As a note, the snap ring pilot hole diameter is 2.313-inches.
  view full answer...
• Which Capacity Jack for a 2002 Viking Pop-Up Camper
  The capacity of the jack you choose needs to be greater than the tongue weight of the fully loaded and ready to tow trailer. I have linked you to an article that explains some methods of determining your trailer tongue weight. It's a good practice to overshoot the capacity quite a bit over and above the trailer tongue weight, if possible. Leaving plenty of cushion will mean that the jack will be easier to crank and will last longer. The Fulton # F1411300301 you referenced has a 1500...
  view full answer...
• What is the Measurement of Fulton Marine Jack from the Floor to the Bottom of the Bracket?
  I think you are on the right track. The Fulton Bolt-Thru Swivel Marine Jack you mentioned, part # F1411300301, is rated at 1500 lb. With the jack fully retracted, the distance from the bottom of the mounting bracket to the floor is 12.5". I think that part # FXP15W is the one you are looking for. It measures 11" from the floor to the bottom of the mounting bracket. On our website, we provide the bracket height for most jacks by measuring from the floor to the center of the bracket...
  view full answer...
• Trailer Jack Solution for Trailer With Bulldog Snap Ring Mount # P9222-00
  The Fulton jack part # F1411300301 you mentioned requires the swivel bracket part # P9012-00. If your plan was to use this jack you'd need to have what's on your trailer now replaced with this bracket and you'd be set. Or for a jack that would mount to the snap ring bracket you have now you'd need the # BD171412.
  view full answer...
• Can I Upgrade the 1200 Pound Jack on My Ranger Boat Trailer?
  From your description, it sounds like you currently have Fulton's 1200 lb. marine jack, part # F1411300301 . Fulton does not make snap-ring jack with a higher capacity. However, Bulldog offers a Round, Snap-Ring Swivel Jack, part # BD151101, that has the 10" lift you need and has a 2,000 lb capacity. It is also offered in a Zinc finish, which is part # BD151109. You would also need to purchase a footplate, part # BD018564, which is rated for 2000 lb., or a wheel, part # BDCP555, which...
  view full answer...
• Replacement Trailer Jack to Fit the Mount for a Shelby 5658A Swivel Jack
  How did your jack attach to its mounting bracket? Is that the single bolt that you mentioned? If so then the only option we have that could work is Fulton jack # F1411300301 which normally uses mounting bracket # P9012-00. And the replacement hardware for that bracket is # F0933325S00. The bolt is a 1/2 inch but it uses that included bushing in the center hole of the mounting bracket.
  view full answer...
• Replacement Trailer Jack for my 2000 Ranger Bass Boat Trailer
  The Fulton Jacks that have the 3"x5.5" bolt pattern are typically the center bolt thru style. For a replacement the Fulton Bolt-Thru Swivel Marine Jack part # F1411300301 is an excellent choice. It will replace the jack only portion of your current setup and is quite easy to swap out. It offers a 1500 lb capacity which will be perfect for your Ranger trailer. I've included a video below for you to check out. Happy Fishing!
  view full answer...
• Recommended Swivel Jack for 2004 Shorlandr Boat Trailer
  for your 2004 Shorlandr trailer, I recommend the MaxxTow Round, Swivel Trailer Jack w/ Dual Wheels # MT70149 for a bolt on option. If you have the welded connection on your trailer, then I recommend the Fulton Bolt-Thru Swivel Marine Jack # F1411300301 or the Snap Ring # FTJ120W0301.
  view full answer...
• What Fulton Bolt Through Jack do you Recommend for my 21' 3.000 lb. Centurion Ski Boat Trailer
  Your 21' Centurion Ski Boat weighs around 3,000 lbs. I always like to use the rule of half. Clearly the jack does not need to lift the entire boats weight but you want one that is not going to have to overwork to lift the tongue either. In that case the Fulton Bolt-Thru Swivel Marine Jack part # F1411300301 is going to be your perfect solution. With it's 1,500 lb. lift capacity it is going to get the job done really well and will last for years! The larger wheel will also make moving...
  view full answer...