Fixed leg, square jack with pipe mount offers increased side-load strength and durability. Jack has 15-1/8" retracted height and measures 9-1/4" from mounting bracket to top, excluding handle. Crank included.
Features:
Specs:
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today were going to review part number BD195362. This is the Bulldog Square Jack with the Square Pipe Mount and the Sidewind Handle. This Bulldog fixed leg, square jack has the square pipe mount that you can release the jack, move it to another position and pin it into place. It has a superior side-load capacity compared with round jacks. The outer and the inner tube will overlap for additional strength when the jack is fully extended and the square design provides additional support for side loading. The side tubular design -- it has the square mount that will weld on to your trailer and then what you can do is just pull the pin out.
Heres the square mount that will mount onto your trailer and then you could put it in the down position or you can move the jack and then pin it in up and out of the way. It has a durable long-lasting construction and a weather-resistant coating on the outer tube and a zinc coating on the inner tube. The sidewind jack is smooth and easy to operate. The square pipe mount and the foot plate are included and I do want to give you a few dimensions on this. The dimension for the bracket height -- now this jack right now is in the fully retracted position, so the height will be measured from the bottom of the foot plate to the center of the mounting tube.
The retracted measurement on this one would be 15.1 inches and to save time I already have a jack that has been extended completely out, right here. What Ill do is give you the measurement on this and again from the bottom of the foot plate to the center of the mounting tube and that would be 30.1 inches. Basically, if you take the 30.1 extended height and then subtract the retracted height of 15.1, it will give you a maximum lift on this jack of 15 inches. One other dimension I want to give you is the clearance height which will be measured from the mounting tube to the top of the jack and this one will measure 9-1/4 inches. The tubing width on this jack will be 2-1/4 inches.
It does have a lift capacity of 3,000 pounds and a static capacity of 5,000 pounds. This part does come with a limited five-year warranty. That should do it for part number BD195362.
Average Customer Rating: 4.8 out of 5 stars (24 Customer Reviews)
Fixed leg, square jack with pipe mount offers increased side-load strength and durability. Jack has 15-1/8" retracted height and measures 9-1/4" from mounting bracket to top, excluding handle. Crank included.We use this product to adjust our fillers up and down. It's a reliable product, and easy to use/install. 333416
Tried to buy this jack locally by stopping at three places, but couldn't. I received exactly what I was looking for and I didn't have to leave my house. Also, they had the best price on the internet. Shawn 730402
so I got these jacks to lift a full size #2000 slide in utility box out of the bed of my pickup truck. I knew they were too short to work but figured I could modify them. so here is how it went. 1. the first thing I noticed was the carriage bolts that keep the plate on that keeps the gearing concealed, well they were stripped and wouldn’t come off. this was consistent on all four of the jacks that I ordered. 2. so after cutting them off to reveal the gearing i found a good bit of grease in the gearing which is a good thing even though they do give you a grease zirk to ease in future greasing which is also good. 3. after tapping out the pin that releases the upper gear and the handle, I found the lower gear also comes off revealing a second pin that holds the outer casing over the screw jacks upper support ( the pin is also used to turn the lifting shaft when you turn the handle ). this seems like a design that will work fine for many years as long as the second pin doesn’t break as it is likely the weakest link in the system ( it doesn’t seem likely to break as long as the jacks inner and outer post sleeves don’t rust together, i also don’t foresee the weight rating to be an issue ). 4. once I had the outer sleeve off I found the upper support (that the lifting shaft screws into to extend the jack) was crimped into the inner sleeve (again not a problen as the weight rating is only #3000 lifting and #5000 static). 5. I cut off the crimped section and pulled out the upper support of the screw mechanism. this piece was a high quality piece of ( what appeared to be stainless) steel that also appeared to be cut from a cnc and it was easy to see what i had to do next. 6. I welded the upper support piece onto the top of a new stick of 3/16 thick 2x2 box tube steel that was 5' tall, this is my new inner sleeve and the only way to extend the jack. if its gonna be tall its gotta be strong. after cleaning the welds which penetrated both the upper support and the new box tube steel without flaw, I re-greased the screw shaft and re-assembled the entire product putting new carriage bolts into the gearing concealment plate. final thought, I was a bit concerned these jacks were a cheaply made product due to the bolts breaking at the very beginning however i was pleasantly corrected the further I broke down the jacks. i do believe they were a worthwhile investment as a necessary tool for the way i use my truck. ie i take this utility box in and out of the bed so i can haul large fifth wheel trailers as im a general contractor. i spent roughly $400 on 4 jacks and 4 sticks of 5' box tube steel and it took me roughly 6 hours to disassemble weld the new inners up and reassemble saving me $800 as the jacks intended for this particular utility box run about $1200 bucks. im a happy camper, good buy 628676
Solid jack and easy to install on our Vermeer chipper. 861468
Good product, good price. These particular stands with a square mount are difficult to find anywhere else. The arrived in a timely manner. Thanks! 824755
The jack is good. A perfect replacement for the one I bent. I am glad I found it. 792600
Super quick shipping. Very happy with p roduct. 713138
Had the exact jack I needed and the ordered was delivered very quickly 698198
used on my log splitter. works great 569867
Arrived on time, well packed exactly as advertised. 560013
Excellent jack. I use them as tongue and stabilizer jacks. 548208
SERVICE AND TIME IN TRANSIT WAS GREAT. 515582
Excellent Customer Service and fast res ponse 513817
very satisfied ,I searched for hours looking for the right jack on line and found etrailer and they had the right jack for my chipper, etrailer shipped it right a way THANK YOU 474128
After a year of sitting outside in the weather and being used a min of once a week it still performs as if it was new. Definitely would recommend 457469
Great product-fast service 333674
Jack works well. 292061
Excellent product and super fast delive ry! 287445
Good product. Does the job nicely. Grease fitting will extend its useful life. 286229
Austin - 11/01/2017Nice product handles lifting to height I need effortlessly. Only thing stopping me from giving 5 stars is that the ball bearing in pin needs to extend out more or be bigger. Michigan roads are bumpy and I made a clip to securead it so it doesn't pop out. As I lost first jack due to pin popping out on bumpy roads 280026
Great jack 277081
very good item. 153053
Well made jack of heavy gauge material. Operates smoothly. Does require either an existing mount or welding of the provided mount to your trailer. 124544
Product was of very high quality and worked perfectly for the application. Ordering was easy and delivery was quick. You have a happy customer at this end. Thank You. 116095
Well Built. Just what the Doctor Ordere d.Thankyou. 100655
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.