Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Loose lug nuts are a hassle you don’t need. This 15" x 5" steel wheel uses beveled stud holes that seat snug against the hub, so once it’s torqued down, it stays put. You’re not constantly checking and retightening after every haul—just solid, dependable hold every time you roll out.
When you’re carrying real weight, you need a wheel that doesn’t flinch. This modular steel wheel is rated for 2,200 lbs and built tough enough for repeated use and long trips. It gives you a strong foundation that holds up through all kinds of conditions without compromising reliability or performance.
A sharp finish matters as much as strength. The white powder coat resists corrosion and keeps its bright color mile after mile, while the modular cutouts give the wheel a clean, straightforward look that works well on any setup.
No guessing here—the common 5 on 4-1/2" bolt pattern and 3.19" pilot diameter make matching hubs simple. Wheel bolt size is 1/2"-20, so fitment is clear and consistent when you’re replacing or adding a spare to your setup.
1. Count the lug holes
Look at the wheel hub or the back of the wheel and count how many lug holes there are(also called bolt holes).
Common configurations include: 4-lug, 5-lug, 6-lug and 8 lug
2a. For even lug counts (4-lug, 6-lug, 8-lug)
Measure from the center of one lug hole directly across to the center of the hole opposite it.
Common configurations: 4 on 4", 6 on 5.5", 8 on 6.5"
2b. For odd lug counts (5-lug)
Measure from the center of one lug hole to the outer edge of the hole directly across (not center-to-center since there's no directly opposite hole).
Common configurations: 5 on 4.5" (most popular), 5 on 5", 5 on 4.75", 5 on 5.5"
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hello everybody, this is Jeff at etrailer.com. Today we're gonna take a look at the Lion's Head, 15 inch by five inch white modular steel trailer wheel with the five on four and a half inch bolt pattern. Now this steel wheel has the modular design, which is sturdy and corrosion resistant. And we say modular design, that's the one that has the round holes all the way around the wheel. The rust resistant finish on this includes a white powder coat on both front and back of the wheel. And if you notice, this wheel does not come with a center cap.
If you do want the center cap, we do sell those separately. You do wanna make sure to get one that would have the same diameter as this pilot hole 'cause when you install that center cap, it does go through that pilot hole. The diameter on this pilot hole is 3.19 inches. If you notice right up here, the valve stem is included. It's pre-installed in the wheel, and this wheel does meet the DOT Department of Transportation and the SAEJ 1204 specs.
This wheel is made in the USA. Few dimensions on this. We're gonna measure the diameter and the width. And when you measure the diameter, you're always gonna be measuring inside to inside or bead seat to bead seat. So if we put our tape measure on it, you can see inside to inside measure 15 inch measurement, a width is gonna be the same way you're measuring inside the inside or bead seat to bead seat.
So the width is five inches wide. Now the bolt pattern on this wheel is a five on four and a half inch bolt pattern. And if you needed to measure that on a wheel like this, that's an odd number of lugs. In this case, five, what you're gonna do is pick one of the holes, let's say this one, and then you're gonna measure across to either one of these holes. But when you measure, it's from the center of the starting hole to the furthest edge of the hole that you measure to.
So in this one, if we measured it be four and a half inches, so it makes it a five on four and a half inch bolt pattern, this does use a wheel lug size of a half inch by 20, and the weight capacity on this wheel is 2,200 pounds. Now we do also offer many other items for your trailer. Just click on the trailer tab that's at the top of our website page. And also if you have any other additional questions regarding this part or any other item we carry, please feel free to reach out to us so that we can get all your questions answered for you. But that's gonna do it for a look at the Lion's Head, 15 inch by five inch white modular steel trailer wheel with the five on four and a half inch bolt pattern.
Customer Satisfaction Score:
90% were satisfied with this product
10% of customers were not satisfied
Ratings & Reviews

Mike
4/28/2021
Excellent no problems
Condition: Surface Scratches
Notes: A single paint chip on the face of the rim. Otherwise in like new condition.
Condition: Surface Scratches
Notes: There are scratches and paint chips on the wheel. Otherwise, new and unused.
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.




Lazer S.
12/30/2025
Glad we could help, Greg! Let us know if there is anything else we can help with! Out of curiosity, what kind of animals do you raise? I like animals. They are delicious! : P