See what our Experts say about this TruRyde Trailer Suspension Parts

• Recommended Equalizer w/ a 6-1/4" Center Bolt to Center Bolt Spacing
  Hey Greg, thanks for the information. To replace your equalizer you'll want the Curved Equalizer for 1-3/4" Wide Double-Eye Springs - 6-1/4" Long - 3/4" Center Hole item # TREQ458. From the way you described yours this matches your dimensions perfectly. It's sold individually. In order to recommend the right shackle and wet bolt kit, I'll need you to measure the distance between the bolt holes on one of the shackles. How did you get your 27" measurement on the leaf springs? A used spring...
  view full answer...
• Replacement Trailer Suspension Components For Tandem Trailer
  We do not have any equalizers with the dimensions you mentioned. From the looks of the photo you sent it appears the hole may be elongated and you may be able to use an equalizer that has all of the holes at 9/16-inch like part # TREQ356, or with a center hole that measures 3/4 inch like part # TREQ458. You will need to measure the equalizer length and height as well as the holes like the attached drawing shows to find the correct replacement. It looks like the shackles and bolts...
  view full answer...
  
• Will The Trailer Ride Height Be Affected By Installing The MORryde Rubber Equalizers # MR87Z?
  With the MORryde Rubber Equalizers # MR87ZR being taller than a traditional Curved Equalizer # TREQ458 will raise the ride height on your trailer if you use your current shackles and straps. MORryde does make the Suspension Upgrade Kit # MR76ZR with 3-1/8" shackle straps measured from center of hole to center of hole. These being longer than the 2-1/4" Kit # MR46ZR will reduce the amount the ride height will change. As the MORryde equalizer is cushioned and provides 3" of travel it is hard...
  view full answer...
• Availability of a Trailer Suspension Equalizer Kit With 6-1/4 Inch Long Equalizers
  We don't offer a equalizer kit that incorporates the # TREQ458 you're needing, but you can obtain the necessary parts separately. We offer a 3/4 inch wet equalizer bolt as part # 126A1. 9/16 bushings with a OD of 11/16 is part # TRBU11566. If you need an OD of 7/8, use part # TRBU11568. You can see the shackle links and bolts we have available by clicking the provided link.
  view full answer...
• Replacing/Upgrading An Equalizer 6-1/4" Long And 4" Tall
  I can certainly point you in the right direction. When replacing an equalizer we want to keep it as close to the stock size as possible. There is a small amount of tolerance, but not much. The Dexter easy flex # K71-653-00 i'm afraid is going to be too big to fit correctly into your suspension. If you want to do an equalizer upgrade, I recommend the Road Armor Shock Absorbing Equalizer # LC696740. This measures 6" long center hole to center hole, and 3-1/4" tall. This will be much closer...
  view full answer...
• EZ Flex Equalizer Replacement Recommendation for Trailer With TREQ458 Equalizers
  The correct EZ Flex equalizer kit you'd need to replace the # TREQ458 that you have is the part # K71-652-00. Both of these equalizers use 9/16 inch diameter bolts too so you'd be covered in that regard as well.
  view full answer...
  
• Recommended Suspension Components For Double-Eye Springs On Tandem Trailer
  We do not have any kits that have all the components with the dimensions you asked for. You can go a couple ways. You can choose to go with the kit you asked about, part # APT4, and then choose different shackle straps. You will need a quantity of 8 shackle straps. We do not have 3 inch shackle straps available. We do have part # TRSL313, that measures 3-1/8 inches center to center. The overall length is 4-3/8 inches. Or you can order the following components separately (2) 6-1/4 inch...
  view full answer...
• Electric Over Hydraulic Brakes, Leaf Springs, Bearings, Hardware, & Brake Lines for Dexter 7K Axles
  Since the ProLube kit # XLPROLUBE2440KIT is only rated for use on 5,200 to 6,000 pound axles I do not recommend using it for 7,000 pound axles. Grease would be better for marine applications since a hub full of grease repels water and an oil bath hub could just let the water set on top. The correct grease seal for disc brake kit # K2HR712D is # RG06-070. It does have an inner diameter of 2.25 inches and the outer diameter at 3.376 inches will fit the hub in the disc brake kit. Spring...
  view full answer...
• Availability of Replacement or Repair Kit for TruRyde Trailer Suspension Equalizer
  We do have a Tandem Axle Hanger Kit # APT4 which comes with the equalizer you referenced, # TREQ458, as well as front and rear hangers, center hangers, shackle straps, shackle bolts, locknuts, wet equalizer bolts, castle nuts, cotter pins and grease zerks.
  view full answer...
• Replacement 6-1/4 Long Equalizers and 2-3/4 Shack Straps For Dutchmen Classic Travel Trailer
  The only equalizer we have available that measures 6-1/4" center to center is part # TREQ458 which a curved equalizer that is 2" tall. If your equalizer is taller you can use Curved Equalizer for 1-3/4" Wide Double-Eye Springs - 6-1/8" Long - 9/16" Center Hole part # TREQ356 that measures 6-1/8" bolt hole to bolt hole and 2-1/2" tall. I recommend CE Smith Shackle Strap - Galvanized Steel - 2-3/4" Hole-to-Hole Length part # CE14103G. To get you the correct replacement axle, I would need...
  view full answer...
  
• Capacity of TruRyde Trailer Suspension Equalizer, Part # TREQ458
  The # TREQ458 Curved Equalizer you referred to is used for 2,000 to 7,000 lb axles, which would give each individual equalizer a maximum capacity of 7,000 lbs.
  view full answer...
• Replacement Bushing for Equalizer part # TREQ458
  The replacement bushing for the center bolt hole of the Equalizer part # TREQ458 is the part # TRBU11566.
  view full answer...

Do you have a question about this Trailer Suspension Part?