3/4" Round. Waterproof mini trailer light with 1 amber LED functions as both a celarance light and a side marker light when properly mounted. Recessed mount with grommet. 2-Wire design with 0.180 bullets. P2 rated.
Features:
Specs:
The waterproof construction of this light makes it ideal for use on trailers that may be submerged, like a boat trailer. The housing and lens are sonically sealed together to create a single unit, which means that water will not get into the light and damage the diodes or circuit board.
Recessed-mount trailer lights install underneath a housing or a grommet, which is often sold separately. These lights will extend into the mounting surface and require that a hole be cut into your trailer.
A P2-rated light produces a 45-degree angle of light to either side of its centerline for a total of 90 degrees of coverage. This beam pattern can be seen straight on, but it cannot be seen clearly from the side. So this type of light can be used as either a side marker light or a clearance light, but it cannot function as both. If you need both functions, then you must install 2 separate lights on your trailer - one as a front or rear clearance light and one as a side marker light.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hi everybody, Andy here with etrailer.com and today we're gonna take a look at this Uni-Lite round submersible amber lens LED clearance or side marker trailer light. With this little 3/4 of an inch round waterproof LED mini trailer light, you're gonna be able to haul safer, by alerting other drivers of your trailer's position and direction of travel. As you can see, I already have this connected to a power source and this light functions as both a clearance and side marker light when properly mounted. Let me go ahead and turn my lights off here in the studio so you can get a better idea just how bright this is. So I'm just gonna shine this here on my table and then let me go for a wide shot here real quick. So it is pretty bright for just being one LED here.
And zooming back in here, let me turn my studio lights back on here for you. Now this one white LED underneath this amber lens can last up to 50 times longer than your regular incandescent lights. They're more efficient, they're gonna provide brighter light with less power output and there's no bulbs to replace, no brittle filaments to worry about. Now this is a P2 rated light, meaning it produces a 45 degree angle of light to either side of its center line for a total of 90 degrees of coverage. This beam pattern can be seen straight on but it can't be seen clearly from the side.
So this type of light can be used as either a side marker light or a clearance light but it cannot function as both. If you need both functions then you must install two separate lights on your trailer, one as a front or rear clearance light and one as a side marker light. There is a lifetime warranty on this LED and this has a power draw at 12.8 volts. It is 0.047 amps. Now this is a two pigtail installation, so let me go ahead and pull my clips off of here real quick so I can show that to you.
And as you can see here, there's male bullet ends and these are the 0.180 male bullet ends. The overall length of the wire is about 8 inches long and this has a durable polycarbonate housing and an acrylic lens and the durable surface mount technology construction of the LED circuit board is going to better withstand shock, moisture and vibration and also allows for improved heat distribution and thinner construction. The waterproof construction in this light is going to make it ideal for use on trailers that may be submerged, like a boat trailer. And the housing and lens are sonically sealed together to create a single unit, which means that water will not get into the light and damage the diode or the circuit board. This is a recessed mount with the included grommet and the installation requires an 11/16 of an inch hole at the desired location.
Now we do have a diagram of additional measurements of this light on this product page, so if you are in need of that, feel free to scroll down a little bit on the bottom to the bottom of this product page for that diagram and those additional measurements. This is DOT compliant and PC rated, and that's gonna conclude our look today. I do hope that it was helpful for you. Again, my name is Andy. Thank you for joining me..
Ratings & Reviews
I have purchased lights from etrailer several times and the service and quality have been great. I have purchased lights for my truck and also have used there submersible lights for my boat trailer.
lights have been in service for over a year and still bright as the first day I installed them.
Shipping was slow, but I can't complain much considering it was free!
I chopped the fenders on my 2008 Jeep Wrangler, which involved removing the side marker lights. I installed a pair of these DOT approved lights to meet inspection requirements.
As for the lights, they are well-constructed and very bright. Installation was difficult; even after drilling and deburring a 11/16" hole, the grommet barely fit in. I had to put a small amount of grease on the light's lateral surfaces before the light would slide into the grommets.
Overall, I am very pleased with the product. Poison Spyder sells an inferior product at several times the price; I am glad I found these here!
These are really nice marker lights. Nice and bright.
These are really nice marker lights. Nice and bright.
Very well built, sturdy and totally sealed against moisture. I installed these into the top of my Haulmark enclosed trailer to act as clearance lights. Installation was a breeze, I just drilled a 3/4" hole with a step bit, wired all five lights together and tied it into the running lights of the trailer's harness. I put the ground against the steel frame. I went a step further and put a bead of clear marine grade silicone around the light to ensure no moisture makes it inside the trailer despite these being a tight fit. As you can see from the pictures, installation is clean and they're very bright, both day and night! I put one on either end, 6" from the sides and the three middles ones are spaced 10" apart. Similar to the clearance lights on a truck, I didn't use a template, just winged it.
Great little running light puck! Easy to install and very bright at night and is even very visible in daylight. Only about an inch in diameter on the outside, you wouldn't think it was much larger from the amount of light they provide.
I actually purchased these lights to use as a side marker light on my Jeep Wranglers after installing after market fenders. Lights have worked fantastic up to this point
These were designed as a clearance light application and at a great price. I bought them to use as turn signal lamps on my RZR. They are high quality and extremely bright when lit, so they work great for both applications. These guys have great parts at a great price and quick shipping. I would recommend them to anyone needing trailer/boat/lighting. Thanks guys.
Great addition to the basic, rear brake lights of a camp trailer.
I added these LED RED to the brake/turn function, within the existing, small holes in the rear bumper--much more apparent when stopping/turning.
These sealed LED lights are very common on larger trucks and trailers now. Easy to install and very robust assembly...priced right!
Perfect fit. Fast shipping
I have finally finished the install of the great products that I’ve purchased from Etrailer. Curt 24K 5th wheel hitch, the lube discs, the front receiver hitch tube, the Factory 7-way connector and 7 -way extension (I have 3 7-way plugs on my truck) and the countless number of LED lights. The service is amazing and the customer service I received was fabulous. I really like these folks as they were vary knowledgeable about what I was after and pointed me in the right direction to accomplish my end goal. Thanks to everyone at Etrailer. I couldn’t have done it all without you.
I bought a couple more of these two-diode LED clearance lights to add some more lighting to the rear of my kayak trailer. They work nice and are easy to install in 3/4" holes that I drilled through a piece of aluminum angle. The trailer has orange clearance lights on the front sides, red clearance lights on the back sides, the stop/turn/parking lights on the back, three red clearance lights on the back, and a white LED license plate light. It's really lit up and very visible at night from the rear and sides. Thanks to etrailer.com for great products and services!
My wife and I like to kayak, but we don't like to deal with putting our kayaks on roof racks on the top of a car. So I bought a used Load-Rite trailer that was designed to hold one Jet Ski, and added a frame made of slotted angle and 2x6 lumber to hold the kayaks, and a cargo box from Tractor Supply to hold kayak seats, life jackets, towels, sun-protection clothing, and some spare gear (ropes etc), and bought all new LED lighting from etrailer.com. The paddles are too long for the cargo box so they have to go in the car! The kayaks are tied down to the trailer with several ropes front and rear, so there is a lot of safety factor in the design....I don't worry about the kayaks coming off the trailer! The entire rig works great....when we return from a kayak trip we just back the trailer in the barn and it's ready to go for our next trip. I put a 5" diameter wheel on the trailer just behind the hitch so I can push it around on flat level surfaces. See the pictures.
The lights are perfect as were the previous ones. I’m always doing projects and these are my go to lights for markers and clearance lights.
These are excellent lights. Very small and compact with a very bright output. I used these as marker lights on the rear of my pickup, and it made a huge difference in visibility. Being only 3/4", you can install these in a variety of locations and for a multitude of applications. I highly recommend these and will be purchasing more for additional lighting needs.
Parts were shipped quickly and accurately. Quality was excellent and parts were received as described.
Great product, fast shipping. I’m very pleased
Great item. Nice and bright and wire pig tale is the right length to work with. 5 stars to etrailer as well. Fast & Secure shipping every time. Thank you
Installed new these new side marker lights wheel wells, the location of the old lights were a more forward and would get broke by rocks. These worked great and are bright.
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.