Replacement passenger's-side hydraulic drum brake. Dacromet backing plate and e-coated shoes fights rust and corrosion. 12" x 2" Assembly is compatible with a hand brake (sold separately). Fits 14-1/2" and larger wheels.
Features:
Specs:
Backing up your trailer might be the only time you don't want the brakes to work. Normally, this would be a job for the reverse lockout on your hydraulic actuator. But if you don't have a lockout, you'll need brakes that will you allow you to back up freely instead.
How do they work, you ask?
During normal forward braking, a fall-away shoe expands to catch your brake drum with enough force to bring your rig to a stop. When driving in reverse, however, these brake assemblies prevent the shoes from fully catching on the drums. This takes away your braking control, allowing the wheels to continue to turn.
Note: Free backing brakes don't activate when you're in reverse. So, keep in mind that a trailer breakaway kit will not be effective if your trailer were to disconnect from your tow vehicle while you're backing up.
If you're looking to customize your boat trailer, opting to attach a parking brake cable to these brakes will make sure you get a little extra security when parking your trailer on steep inclines.
Installing these brakes is easy, and using them is even easier. Run the linkage cable from your tongue-mounted handbrake (T2385200 - sold separately) to the lever on the backing plate of the assembly. Then, just pull on the handbrake any time you need a little reassurance that your valuable cargo won't roll away from you.
If your trailer is routinely exposed to saltwater or heavily treated salt roads, these are the brakes for you. You'll get the best corrosion protection that drum brakes have to offer. The first layer of anti-corrosion coating is an e-coat primer applied to the shoe levers. Next, a Dacromet coating goes on. And finally, an acrylic topcoat that's nearly rustproof is put onto the backing plates. You'll also find stainless steel springs inside that are rustproof.
The more miles you put on your trailer, the more your brake pads will wear down. As they lose contact with the drum, stopping distances get longer and longer. To keep your brakes working great, it's important to adjust them pretty routinely. For this job, grab a floor jack and either a brake adjustment tool (sold separately) or just a standard flathead screwdriver.
Jack up your trailer enough to get the wheel(s) off the ground. Remove the adjuster plugs from the backing plate on the brake, and insert the flat end of the tool through the back of the assembly.
Push in on the star gear and lift it up. Keep doing this until the brake pads catch on your brake drum. When you can't spin your wheel by hand anymore, back the gear off by about 10 clicks (push down on the star gear). Does the wheel now spin freely (even if it sounds like the brake pads drag slightly on the drum)? Great! Then you're all done with that one and ready to adjust the rest.
Once you get these assemblies installed, and your lines flushed with fresh fluid, you'll need to break in these brakes. First, find a long stretch of road or a big, empty parking lot. Speed up to about 40 mph and brake to slow to about 20 mph. Repeat this 15-30 times. The goal is to get the brake shoes properly seated into your drum. You'll know you've done that when it feels less jerky (and more consistent) each time you apply the brakes.
Note: The brakes will be very hot after doing this, so after every 10 stops you'll want to wait about 10 minutes to let the brakes cool off before continuing. If you don't, you might cook and crack the pad material.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hello everybody, this is Jeff etrailer.com. Today we're gonna take a look at the Dexter 12 inch by two inch, corrosion resistant, right hand free backing hydraulic trailer brake assembly with the parking brake for 7,000 pound axles. Now this hydraulic drum break assembly is designed for use with the surge type trailer brake actuators. This one here is a free backing design, which means it'll let you reverse without your trailer brakes being activated. And the way it does it is the hydraulic pressure is contained by the wheel cylinder and the brake shoe will turn and release the pressure when it's reversing. And the way you can tell a free backing assembly, is it has this D shaped shoe to it.
You can see this one shoe over has a D designed to it. Now these brake shoes are lined with an automotive grade friction material. This friction material is fully bonded to the shoe. It's not riveted. Gives you a lot longer life, more breaking torque.
Also on this one, the backing plate, if I spin it around, you'll be able to see it. This whole backing plate is coated with a corrosion resistant finish and it does use stainless steel springs. So this is great for marine application. Now, this is a right hand passenger side brake assembly and the way you can tell that, now when you get a new one, of course, there'll be a sticker on it that'll say right hand or left hand. This one will say right hand on it.
And that's the easiest way. But if that sticker wasn't there, a little tip to know that to how you can tell by looking at it is you look at the size of the brake pad or the lining on the shoe. So you look at this shoe the pad goes all the way from here to here and if you look at this one, it just goes from here to here. So this is a shorter shoe. The shorter shoe is the primary shoe.
That primary shoe will always face the front of the trailer. So if it's gonna face the front, you can see that it'll go on the right hand or passenger side. That's the best way to tell if it's a right or left hand side assembly. Now this is a manual adjustment. In other words, this adjustment wheel down here, you will have to manually adjust. It does require periodic manual adjustment. This one here also includes this parking lever right here. You can see this parking lever will work with a trailer that already has a parking brake. If you do not have a parking brake and you do want to add a parking brake, we do sell a manual parking brake separately on our website that can be added to this assembly here. That manual parking brake part number is T 2 3 8 5 2 0 0, and it's usually listed on this product page as a related product. Now, if you notice the five nuts here, with the washers attached, that's the mounting hardware. The mounting hardware is included. This part is made in the USA. Again, the specs on this, it's designed to fit axle ratings of 7,000 pounds. Now the size on it, when we say it's a 12 inch by two inch, the 12 inch that's gonna measure when you measure it, it's the diameter from this shoe to this shoe. So if we take the ruler and we go this shoe to this shoe, there's your 12 inch measurement and the two inch is the width of the pad. So, if you measure the width of the pad on there, it's two inches wide. So, that says this is a 12 inch by two inch assembly, does require 12 inch brake drums. The mounting flange right here, is a five bolt design that goes, that mounts to the brake mounting flange on your trailer axle. And the wheel size uses a 16 inch and larger. But that should do it for the review on this Dexter 12 inch by 2 inch corrosion resistant, right hand free backing hydraulic trailer brake assembly with the parking brake for 7,000 pound axles.
Ratings & Reviews
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.








Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.