See what our Experts say about this Inno Roof Rack

• Roof Rack for 2008 Land Rover Range Rover Sport With Naked Roof to Carry SUPs
  The best value for a roof rack for your 2008 Land Rover Range Rover Sport with a naked roof to carry your SUPs is going to be from Inno because it gives you a high-quality aerodynamic rack at a price that is less than other recognizable brands. The parts you need are the following: - Inno Aero Crossbars # INXB153-2 - Inno Through Feet for Aero Crossbars # INXS250 - Custom Fit Kit # INK766 Then to carry either 1 or 2 SUPs I highly recommend the Inno Locker Watersport Carrier # INXA445. The...
  view full answer...
• Recommended Roof Rack For A 2021 Ford Expedition Max Limited
  Hey Chuck, The rails on your Expedition are unfortunately too large for the Malone # MAL84AR to properly clamp to so you'll have to go with another roof rack in order to get a large enough crossbar to get a 4" overhang. I recommend the following components from Inno: Inno Aero Crossbars - Aluminum - Black - 60" Long - Qty 2 # INXB153-2 Inno Through Feet for Aero Crossbars - Raised Side Rails - Qty 4 # INXS150 The 60" crossbars should give you roughly 4-1/4" of overhang on each side...
  view full answer...
• What Inno Aero Bar Roof Rack Parts Are Needed for a 2004 Toyota Tundra
  Yes, the Inno Roof Rack part numbers # INXB153-2, # INXS250, and # INK532 have been confirmed as a fit for your 2004 Toyota Tundra so it would fit and work well for you.
  view full answer...
• Which Roof Rack Is Best For Installing Thule Hullavator Kayak Carrier On 2021 Honda CR-V?
  I can certainly help you out with that. First off, the Thule Hullavator # TH898 requires crossbars that hang over the edge of your vehicle's roof by at least 4" on each side. Second, the Hullavator also weighs 40lbs, so you will need a roof and a roof rack with a weight capacity to handle the 40lb carrier along with your kayak. It looks like your roof can hold up to 165lbs but you will want to check your owner's manual to verify. Since you have the touring model, you likely have flush...
  view full answer...
• Roof Box Compatiblity 2015 Ford Explorer W/ Panoramic Roof
  Generally speaking, a cargo box like the Thule Force XT Rooftop Cargo Box part # TH6358B can be used on vehicles with a sun, moon or panoramic roofs. However, it is not recommend you open the roof opening while the cargo box is installed due to noise and possible clearance issues. A moon roof will not have problems with clearing the crossbar as they do not extend up past the roof line. A sun roof however does. Therefore you will want to ensure you do have clearance between the sunroof...
  view full answer...
  
• Recommended Roof Rack For 2018 Chevy Traverse With Naked Roof
  Thanks so much for the photo, and it shows your 2018 Chevy Traverse has a naked/bare roof. And the roof rack that fits actually uses clips that grasp onto the door jamb, so they don't actually fit into a channel. The best roof rack for your '18 Traverse is one that installs that way, from Inno: - Inno Aero Crossbars # INXB153-2 - Inno Through Feet for Aero Crossbars # INXS250 - Fit Kit # IN63FR This is the best roof rack for your Traverse with a naked roof because it is the quietest,...
  view full answer...
  
• Measuring the Front and Rear Bar Stay Dimensions for Inno Roof Rack on 2009 Scion xB
  I have the exact measurements to fit the Inno Roof Rack with part numbers # INXB153-2 (or # INXB123-2), # INXS250 ( or # INXS200), and # INK300 on your 2009 Scion xB. It sounds like the confusion comes from how there are different install instructions for the different parts and they must be used simultaneously. What will help you out here is the install guide for your fit kit # INK300. These are the clamps and pads that were designed specifically for your 2009 Scion xB. What you're looking...
  view full answer...
• Roof Rack Recommendation for 2009 Scion xB for Carrying Roof Box
  For your 2009 Scion xB the Inno Aero Bar roof rack part numbers # INXB153-2, # INXS250, and # INK300 would be a great solution. The aero bars are quieter than square bar roof racks and the minimize fuel mileage loss. The Sears X-Cargo Box that you have would work well with this kit.
  view full answer...
• Recommended Roof Rack And Fit Kit For A 2008 Scion xB
  I spoke with my contact at Thule, and unfortunately there is not a fit kit to fit your Thule Wingbar Evo to your 2008 Scion xB. With that being said I know it's not what you'd like to do, but If you need a roof rack you're going to have to get a new setup, unfortunately. I recommend checking out the Inno Aero Crossbars # INXB153-2, with the feet # INXS250, and the fit kit # INK300. These crossbars measure 60" (152 cm) 3-1/8" wide x 1-1/8" tall, and has a maximum weight capacity of 165-lbs.
  view full answer...
• What Roof Rack Set Up Works with My 2020 Chevrolet Traverse with a Bare Roof?
  For a great roof rack for your 2020 Chevrolet Traverse with a bare roof, I recommend the following parts: - Inno Aero Crossbars - Aluminum - Black - 60" Long - Qty 2 # INXB153-2 - Inno Through Feet for Aero Crossbars - Naked Roofs - Qty 4 # INXS250 - Custom Fit Kit for Inno XS200, XS250, and INSU-K5 Roof Rack Feet # IN63FR With this roof rack system, you will be able to transport cargo and accessories up to 120 pounds. The Through Feet come with locks to secure the system to your roof...
  view full answer...
• What do I Need to Haul a Kayak on my 2013 Ford Explorer Using a Lockrack Kayak Carrier
  We can get you set up. For crossbars I recommend the INNO Aero System using Inno Aero Crossbars part # INXB153-2 and the Inno Through Feet for Aero Crossbars part # INXS150. With that installed the Lockrack Adjustable Watersport Carrier part # LR24VR you looked at will be a perfect way to get you kayak out where you want to use it.
  view full answer...
• Inno Aero Roof Rack Recommendation for 2018 Ram 1500 Quad Cab
  For your 2018 Ram 1500 quad cab the Inno Aero roof rack crossbar length recommended is 60 inch like the part # INXB153-2, # INXS250, and # INK653 so that is what I would recommend you go with.
  view full answer...
• Lowest Profile Roof Rack for a 2016 Audi A6 Sedan
  The lowest profile roof rack for a 2016 Audi A6 Sedan is the Inno Aero Crossbar System part # INXB100-108, part # INXS200, and part # INK412. This system sits about 3-1/2" to 4" from the roof to the top of the crossbar but it is hard to get exact measurements due to all the different roof shapes. I have attached a photo of the Inno Aero Crossbar System installed on a different vehicle that way you can get a better feel for how tall it is.
  view full answer...
  
• Recommended Roof Rack for Fiat 500x With Panoramic Glass Sunroof
  There is a roof rack that will fit your 2016 Fiat 500X that has the panoramic sunroof, the Inno Aero. This rack is made up of Aero Crossbars # INXB100-108, Flush Feet for Aero Crossbars # INXS200, and Custom Fit Kit # INK482. This rack has a 100 lbs weight capacity though I do recommend checking your Fiat's manual to confirm what the actual capacity is. The aero crossbars are going to give you a quiet ride and they also have integrated T-slots so you can carry accessories that way. I've...
  view full answer...
  
• Recommended Roof Rack and Track System for Truck Topper to Carry Canoe on 2012 Toyota Tundra CrewMax
  We can get you the parts needed to install a roof rack on your truck topper so you can haul your canoe. There are advantages to systems in regards to quality and value, and for your application the best fit is from Rhino-Rack, who is known for their quality, which is consistent with other brands, but often not with as high a price tag. What I recommend is: - Rhino-Rack Aero Bar Roof Rack for Camper Shells - Track Mount # Y02-490B This will give you 59 inch crossbars on your camper shell,...
  view full answer...
• Can Leg on Rola Roof Rack be Replaced for 2006 Honda Civic
  We do have the following parts still listed as replacement parts for a Rola roof rack: Replacement Cage Nuts part # 59710 Replacement Wrenches part 38371 Replacement Rubber Buffer Strips part 59846 (discontinued) Replacement End Support Covers part # 59887 For your application though if that leg is damaged badly then we need to get you a different roof rack. When I reached out to my contact at Rola he said that part has been discontinued so there aren't any replacements for you. If your...
  view full answer...
  
• Recommended Inno Roof Rack For 2013 Honda Civic Coupe Naked Roof
  The custom fit kit part # INK642 that you referenced is the correct fit kit for the 2013 Honda Civic Coupe. To complete the roof rack system you will need Inno Aero Crossbars part # INXB130-138 and Inno Through feet part # INXS250. The Inno crossbars are aerodynamic to cut down on wind noise and have integrated T-slots to make mounting accessories easier. The through feet are designed so the bar sits on top of the feet and allows for bar overhang, which comes in handy if you have a water...
  view full answer...
  
• Roof Rack Recommendation For A 2024 Honda CR-V Sport L
  Hello Ken. We do have roof rack options for your 2024 Honda CR-V Sport L. Does your CR-V have the OEM flush mounted rails that run front to back? I ask because we offer roof rack option for both naked roof vehicles as well as vehicles with the OEM flush mounted rails. So, I will go ahead and recommend options for both roof styles: OEM Flush Mounted Rails - Thule WingBar Evo Crossbars # TH711300 - Evo Flush Rail Feet for Thule Crossbars # TH710601 - Fit Kit for Thule Evo # TH52KE Naked...
  view full answer...
• Roof Rack and Kayak Carrier Recommendation for 2018 Lincoln MKX
  The roof rack I recommend for your 2018 MKX with a naked roof is the Inno Aero Bar roof rack part numbers # INXB115-2, # INXS200, and # INK676 because this custom fit rack has aero bars which are very quiet, installs very easily, and we know it fits and works well on the MKX as we had the chance to install the rack on one. Check out the linked install video I attached for this rack to see us walk through the install of the rack on a 2015 MKX. Then for a kayak rack I recommend the Yakima...
  view full answer...
  
• Roof Rack Recommendation for 2016 Fiat 500X with Smooth Roof
  There is a great option for a roof rack from Inno, who is also the only manufacturer that makes a rack which fits your 2016 Fiat 500X with a naked roof. This will give your 500X a low-profile, sleek and durable roof rack that can carry all kinds of gear. The rack consists of: - Inno Aero Crossbars # INXB100-108 - Inno Flush Feet # INXS200 - Custom Fit Kit # INK482 As you can see by the accompanying photo of this roof rack on a 2016 Fiat 500X the Inno's crossbars fit the exact width of...
  view full answer...
  
• Where to Install Feet of Inno Roof Rack on a 2014 Toyota Prius v
  I'll be happy to help you out with the installation of the Inno parts (listed below) on your 2014 Toyota Prius v: 42" Aero Crossbars - # INXB108-2 Flush Feet - # INXS200 Fit Kit - # INK870 For the front crossbar you will space the feet out at 20-1/2" and position the feet 2" in front of the door edge like you mentioned. For the rear crossbar you will space the feet out 20-3/4" and position the feet 25-1/2" back from the door edge. Attached is a snapshot of these specs out of the installation...
  view full answer...
  
• Inno Roof Rack Recommendation for 2008 Toyota Prius
  The Inno Aero Bar Roof Rack part # INXB108-2, # INXS200, and # INK705 is a great option for your 2008 Toyota Prius. It does come with locks and also the aero shaped bars help minimize wind noise. This rack does install using door clamps and the feet then rest on rubber pads on the roof of your vehicle. Over time these racks hold up just fine. I'd periodically remove the feet and clean them and the vehicle paint to prevent any scratching but even that is really unlikely. Value wise this...
  view full answer...
  
• Roof Rack for 2022 Chevy Traverse with Naked Roof
  For your 2022 Chevy Traverse that has a naked roof we have the Inno roof rack part numbers # INXB123-2, # INXS200, and # IN63FR which would work great. It clamps around the door frame so it's pretty easy to install and remove as well. It would be great for a temporary install or to be left on for a decent amount of time. The bars are aero shaped too which means there would be minimized wind noise.
  view full answer...
• What Is The Lowest Profile Roof Rack For A 2023 Mazda CX30 With Factory Flush Rails?
  Removing the factory rails will definitely be the way to go if you want to have the roof rack sit as low as possible. This way the towers can sit directly on the roof, as opposed to sitting on top of the rails. Removing the rails is actually something we recommend fairly frequently for a 2023 Mazda CX30. For you I recommend the Thule WingBar Setup. The towers and crossbars will add only about 4-1/8" of height to your roof. This consists of the following parts; Thule Wingbar 53" # TH711400 Evo...
  view full answer...
• Crossbar Spacing Instructions For The Inno Aero Crossbars On A 2015 Toyota Prius
  The Inno Aero Crossbars # INXB100-108 with the flush feet # INXS200, with the fit kit # INK865 will need to be mounted: -15-3/4" from the gap between the front and rear doors, for the rear, &, -11-3/4" from the gap between the front and rear doors, for the front. I have included a a diagram depicting these measurement for you to check out as well.
  view full answer...
  
• Recommended Roof Rack for a 2015 Honda Civic Coupe
  The Inno Aero Crossbar System part # INXB108-115, part # INXS200, and part # INK642 is a great cost effective option for a 2015 Honda Civic Coupe and what I recommend using. In fact, it is the most cost effective option we have with the aero shaped crossbars. It also has a very sleek design since the crossbars don't extend past the mounting feet. I have attached a full list of options below.
  view full answer...
• Roof Rack Options For 2020 Lexus RX 350 With Panoramic Glass Sunroof
  If your Lexus has flush mounted rails that run back and forth on the roof, I recommend to use the Thule WingBar Evo Aluminum Crossbars part # TH711200 with the feet part # TH710601 and fit kit part # TH186044 for the 2020 Lexus RX350 F sport with panoramic roof. This rack does fit with the panoramic roof however Thule recommends that you do not open the glass roof when the rack is installed because it will damage the roof, the accessories on the rack and create a lot of wind noise. The...
  view full answer...
• Does Inno Roof Rack Fit 2015 Lexus GS 350 Without Doing Any Modifications
  Yep, it absolutely does; I verified for you with the manufacturer that the Inno roof rack does indeed fit a 2015 Lexus GS 350, including your F-Sport model, and you will not have to cut the bars or do any type of modification. For the complete roof rack on your Lexus, you will need the following parts: - Inno Aero Crossbars # INXB108-2 - Inno Flush Feet for Aero Crossbars # INXS200 - Custom Fit Kit # INK418
  view full answer...
• How to Carry Two 65 Lb Kayaks with a 2015 Honda Civic Si
  I looked in the owner's manual for your 2015 Honda Civic Si and was not able to find any reference to what your roof's weight capacity is. Therefore, your best option to determine this would be to contact the dealer with your VIN. Assuming the weight capacity of your roof is rated for the weight of your kayaks/rack/carrier, I recommend using the Inno Roof Rack part # INXB108-115, # INXS200, and # INK642 with two sets of the Swagman Contour Kayak Carrier w/ Tie-Downs - J-Style - Fixed Arms...
  view full answer...
• Are there Any Thule Crossbars for My 2013 Honda Crosstour?
  There is not a fit kit for your 2013 Crosstour because Thule does not make a set of bars compatible with your vehicle. Instead, you're limited to using either the SportRack Semi-Custom Roof Rack for Naked Roofs - Square Crossbars # SR1002, or any of the following: -Inno Aero Crossbars # INXB130-138 for a set of 51" and 54" long bars with the custom feet # INXS250, and the fit kit # INK587, -Inno Aero Crossbars # INXB123-130 for a set of 48" and 51" long bars, with the custom feet # INXS250,...
  view full answer...
• Lowest Profile Roof Rack for 2022 Mazda CX-5 With Bare Roof
  The lowest-profile roof rack for your 2022 Mazda CX-5 is the flush-mounted Inno rack on your bare roof. The overall height added will be 4 inches give or take a small amount (the curves of the roof will mean this can vary). The flush-mount does not shift the mounting point, however, as the feet have to be positioned at specific points on your CX-5, per the instructions. The parts that make up the Inno rack that fit your '22 CX-5 are the following: - Inno Aero Crossbars # INXB108-115 -...
  view full answer...
• Flush-Mount Roof Rack Options For 2018 Honda Civic
  Since Thule recommends 53" crossbars for your 2018 Honda Civic, you will not want to go shorter. This is because going shorter could be too close to the mounting brackets and that will not provide sufficient room to install the Thule system onto the roof. Luckily, there is a flush-mounted system that will fit your vehicle, but not from Thule. If you have the hatchback then go with Rhino-Rack ROC25 Roof Rack # RR78TR and if you have the sedan then go with Rhino-Rack ROC25 Roof Rack # RR92XR....
  view full answer...
• Thule Flush Mount Roof Rack For 2005 Toyota Prius
  The Thule AeroBlade roof rack has been discontinued and replaced by the WingBar Edge, so there isn't a fit kit for those crossbars for your 2005 Toyota Prius. If you'd like a Thule flush mount roof rack for your '05 Prius you can use the Edge, which consists of Thule WingBar Edge Crossbar - Silver # TH23RE or Black # TH56FE, Edge Clamp Feet # TH79SC, and Fit Kit for Thule Evo Clamp and Edge Clamp Roof Rack Feet # TH145181. This is a premium option so if you'd like something that is still...
  view full answer...
• Aero-Style Roof Rack for 2018 Lexus RX 350 with No Roof Rails
  We can help you with an aftermarket roof rack for your 2018 Lexus RX 350 that has a bare roof with no sort of rails or fixtures. The current options come from Inno, a prominent maker of OEM roof racks for many import vehicles. Their three rack systems for your RX 350 are shown on the linked page. The first two racks shown use longer cross bars which extend out past the mounting legs to give you the most available cargo space. The last one shown uses shorter bars that terminate in the...
  view full answer...
  
• Recommended Solution to Carry 4 Bikes on 2017 Mini Cooper 4 Door with Hardtop
  I have a solution for you, but the Curt # C11417 is not a confirmed fit on the 2017 Mini Cooper; it is designed for older models of the Mini Cooper only. The only available hitch confirmed to fit the 2017 Mini Cooper (excluding S and John Cooper Works editions) is the EcoHitch # 306-X7290, which has a 1-1/4" receiver. With that said, this EcoHitch is a Class I hitch with a 150-lbs tongue weight capacity and you cannot carry 4 bikes on a Class I receiver. I'll also note that you would...
  view full answer...
• Why are Roof Rack Crossbars Different Lengths for a 2007 Acura MDX with Naked Roof
  You have to consider the whole system and how the designs are different. Since they are all different the bars won't necessarily be all the same. There are some designs, for example from Inno, that have bars that are even shorter because the way the feet are designed they have to be a certain length. If you want to go with a quality aero bar roof rack the Rhino-Rack is a great choice. You will need the following parts to install it on your 2007 Acura MDX with naked roof: 2500 Roof Rack...
  view full answer...
• Parts Needed to Add Old Thule Square Bars to 2022 Ford Maverick
  Hi William; it sounds to me like you have the old Thule square bars. The current SquareBar Evo Crossbars like the ones found in the # TH52EG have a channel underneath for mounting. The old bars do not have this channel. If I'm right, and you have the old style bars, you will need the Inno # INSUT and # INK856 to mount them on your 2022 Maverick. Inno square crossbars share the same dimensions and Thule feet for this style are discontinued so this is the only solution. If they happen to...
  view full answer...
• Roof Rack for Old Thule Square Crossbars on 2022 Ford Maverick
  Thank you for all of the information! Since you're wanting to use your older Thule square crossbars you will need to use the Inno legs and fit kit as Thule updated their roof rack system a few years ago and their newer legs don't work with the older square bars. The Inno square bars have the same dimensions as the older Thule bars though which is why their kits are compatible. As of right now (January 2022) the only roof rack fit listed that fits this criteria is for the 2022 Ford Maverick....
  view full answer...
• What Kayak Rack will Work with My Tonneau Cover on My 2022 Ford Maverick?
  I have a great kayak carrier solution for you that works with your trifold tonneau cover. Unfortunately, I confirmed with our ladder rack manufacturers that we currently do not have a fitment of a ladder rack that will allow you to simultaneously install the rack with the cover installed. However, we do have a great roof rack option that allows you to transport your kayaks on the roof of your 2022 Ford Maverick to allow you to have a fully-functional tonneau cover. For that route, I recommend...
  view full answer...

Do you have a question about this Roof Rack?