Hopkins RV Leveling Kit with Electronic LED Smart Level

Hopkins RV Leveling Blocks - HM0820K

Quickly and easily position your RV so that it's level at the campsite. Attach the ramps to the tops of lumber (not included) to create leveling blocks that are simple to drive up. LED leveling device shows if your trailer or RV is level.

Features:

• Heavy-duty kit lets you create a system to level your trailer or motor home
  • Build leveling blocks, then use electronic level to determine how many blocks are needed and on which side
• Durable levelers are created out of included plastic ramps and 2x8 lumber (not included)
  • Customizable - cut wood to fit your application
• Wheel docks attach to top board to prevent tire from rolling once RV is leveled
• Wheel chock keeps your trailer or RV from moving while it's parked
  • Place chock under a wheel on the opposite side of your RV after it is leveled
• Non-skid traction mat goes under leveling blocks to limit their movement as you drive up
  • Can be wrapped around leveling blocks when not in use to be used as a carrying strap
• Bright green ramps and docks make it easy to see when your RV is centered on blocks
• Easy-to-use electronic level helps you level your trailer or motor home when parking at the campground
  • LED display uses lights to indicate how many leveling blocks need to be added or removed to get your RV level
  • Hinged design allows both front-to-back and side-to-side leveling
  • Power-saving design - automatically shuts down to save battery power after 1 minute of inactivity
  • Built-in bubble level acts as a backup in case the battery dies
  • Weatherproof casing attaches to RV with adhesive backing
• Kit includes 4 ramps and 2 docks to create 3 leveling blocks, 1 wheel chock, 1 traction mat, 1 Smart Level device, and assembly hardware
  • AA battery for level not included

Specs:

• Maximum amount of additional leveling height: 4-1/2"
  • Additional leveling height per block: 1-1/2"
• Ramp dimensions: 3" long x 7-3/16" wide x 1-1/2" tall
• Dock dimensions: 6-9/16" long x 6-3/4" wide x 1-1/2" tall
• Chock dimensions: 8-3/4" long x 7-1/4" wide x 4-15/16" tall
• Traction mat dimensions: 24-1/4" long x 6-1/2" wide
• Level dimensions: 4-7/8" long x 3-1/2" wide x 1-1/8" thick
• Warranty:
  • 3 Years for ramps, docks, and chock
  • 90 Days for electronic level

Durable Wooden Support

The Hopkins RV Leveling Kit uses durable wood (not included) to support your RV during leveling. Plastic leveling blocks sink into soft surfaces and can bend easily when your heavy RV is on top of them. This can lead to the blocks cracking or even breaking, which can cause damage to your RV's wheels and axles. The ramps used in the Hopkins leveling kit attach to lumber to create thick, sturdy supports for your RV that won't bend or break.

Blocks are Customizable and Easy to Assemble

The Hopkins RV leveling kit can be easily customized to fit your RV's wheels. This is because it uses 2x8 lumber (actual dimensions: 1-1/2" x 7-1/4") that you cut to size. For the best fit, place the wheel docks on either side of one of your RV's tires, so that your wheel sits between them. Measure from far edge to far edge of each dock and cut the lumber to that length. This board will become the top leveling block. If you have a tandem-axle setup, the board will need to be cut to accommodate both wheels.

After measuring and cutting the lumber, attach the wheel docks to each end of the board with the included screws. Unlike traditional leveling blocks, which typically don't have tire stops built in, the block that is made with the wheel docks keeps your tire from rolling forward or backward off of the leveler.

The length of the other 2 leveling blocks will be based on the length of the top leveler. To create the middle leveler, just cut the board to be 6-1/4" longer than the top piece. The bottom leveler will need to be 12-1/2" longer than the top board. Attach the treaded ramps on top of the boards on each end with the included screws.

Simple to Use - Level Your RV Without the Guesswork

The included electronic Smart Level is specifically designed to work with the Hopkins leveling ramp kit to make leveling your RV or trailer as simple as possible.

Each red light that appears on the Smart Level means that 1 leveling block from the kit must be added on that side of your RV or trailer. No extra calculations or guesswork - simply read the display and add the blocks that you need.

Each leveling block adds 1-1/2" of increased height for a maximum of 4-1/2" of additional height. Begin by using the top board (the shortest board). Place it in front of the wheel on the side of the RV that you need to raise. Slowly drive your RV up the leveler and over the plastic wheel dock.

Once the wheel is set in between the 2 docks, check the Smart Level to see if the RV is level. If your RV is still too low on that side, reverse off of the leveling block and add the middle block. To do this, set the top leveling block between the 2 treaded ramps on the middle block, nesting it in place. Then drive back onto the levelers until your tire is between the wheel docks. Check your RV's level. Add the third block if necessary.

Once your RV is level, the middle green light on the Smart Level will illuminate. At this time you can secure the tire on the opposite side of your RV with the included wheel chock.

The Smart Level's display is hinged, so it can be used for both front-to-back and side-to-side leveling. When the level is folded in alongside the RV, it will measure front to back. Swing the level out so that the display is perpendicular to your RV, and it will measure side to side. The hinge also allows you to swing the level out 180 degrees so that it can be seen from the driver's seat using your rearview mirror.

08200 Hopkins Leveling Block Kit for RVs with Wheel Docks and Chock

08201 Hopkins Electronic LED Smart Level for RVs and Trailers